COSMOGAS POOLDENS 100T, Инструкция по установке, эксплуатации и обслуживанию

Страница: 89 / 96

89
POOLDENS
COSMOGAS
Parameters Parameters
Ref. Parameter description Adjustment field F a c t o r y
value
Single burner
(mod. 34T, 60T and 70T)
Burner 1 (Master)
(mod. 100T, 115T, 140T,
180T, 210T and 280T)
Burners 2 to 4
(mod. 100T, 115T, 140T, 180T, 210T
and 280T)
Personalised
values
3001 Burner operation address 0 = Not in cascade,
1 = Burner 1 (Master),
2 to 4 = Burners 2 to 4 (slave
burners)
2 1 1 from 2 to 4
3002 Fan adjustment field from 0 to 4
0
34 and 60 = 0
70 = 2
100 and 115 = 0
140, 180, 210 and 280
= 2
100 and 115 = 0
140, 180, 210 and 280 = 2
3003 Unit of measurement of display C = °C and bar;
F = °F and PSI;
C C C C
3004 Water pressure switch 0 = Disabled; 1 = Enabled;
2 = N/A; 3 = N/A
1 1 1 0
3005 Burner flapper valve 0 = Disabled; 4 = Enabled;
8 = N/A; 12 = N/A;
4 0 4 4
3006 Water flow rate sensor 0 = Disabled; 16 = N/A;
32 = N/A; 48 = Enabled
48 48 48 48
3007 Condensate level sensor EnAb = Enabled;
DISA = Disabled
Enab Enab Enab dISA
3008 Exhaust gases type sensor SEnS = Sensor; StCH = Switch SEnS SEnS SEnS SEnS
3009 Type of external sensor 10 = 10kohms; 12 = 12kohms; 10 10 10 10
3010 Type of other sensors 10 = 10kohms; 12 = 12kohms; 10 10 10 10
3011 pump mode 0 = primary c pump; 1 = N/A;
2 = N/A; 3 = N/A;
0 0 0 0
3012 DHW operation mode 0 = only central heating;
1 = storage tank with puffer;
2 = storage tank with thermostat;
3 = N/A; 4 = N/A; 5 = N/A
0 0 0 0
3013 Reset Err 115 EnAb = Enabled;
DISA = Disabled
Enab Enab Enab Enab
3015 Climate regulation: maximum central
heating delivery temperature (this
parameter is overwritten by parameter
3017)
from 20°C to 90°C
82 °C N/D N/D N/D
3016 Climate regulation: minimum central
heating delivery temperature
from 20°C to 90°C
20 °C N/D N/D N/D
3017 Maximum delivery temperature (this
parameter takes priority over parameter
3015)
from 20°C to 90°C
50 °C 50 °C 50 °C 50 °C
3018 Minimum delivery temperature from 20°C to 90°C 20 °C 20 °C 20 °C 20 °C
3020 Type of water flow rate sensor 0 = N/A; 1 = DN8;
2 = DN 10; 3 = DN 15;
4 = DN 20; 5 = DN 25
4 4 4 4
3022 Minimum water pressure from 0 to 5 bar 1 1 1 1
3035 Minimum water flow rate from 0 to 100 l/min 75 75 75 75
3050 Number of slave burners from 0 to 3
3 0
100, 115 and 140 = 1
210 = 2
280 = 3
3
3085 Modbus address from 0 to 126 1 1 1 1
3086 Number of Stopbits 1 or 2 1 1 1 1
3100 Material selection ABS; CPVC; PVC; SST; PP. PVC PVC PVC PVC
3101 Nation selection US, CA US US US US
“ S 4 ”
switch
“S4” Switch Position (see fig 16-11 and
16-12)
On or Off
On On On Off
N/A = Not Applicable
WARNING!
Changing these parameters could
cause malfunctions of the appliance and therefore also
of the system. For this reason only a professionally
qualified technician with awareness and in-depth
knowledge of the appliance can change them.
WARNING!
By going into the forced menu the
appliance may start working; paying no regard to this
may cause harm to people, animals or things.
WARNING!
If it is a multi-burner appliance
(models from 100T to 280T) the display is always
connected to burner 1 (MASTER); to set the parameters
in the other burners you need to connect the display to
them as shown in section 16.8.
The forced menu allows the appliance to be set according
to the system to be provided. Setting is done by adjusting
the parameters available (shown in the table).
To access the forced menu, proceed as follows:
1 - Turn off electricity to the appliance by moving the main
switch to OFF;
2.- Hold down both the RESET and the
▼
button and
move the main switch to ON;
3.- Wait for the display to show the word “INIT” or the
parameters
3000
.
4. - Using buttons
▲
and
▼
scroll through the list of
parameters
3000
;
5.- Browse the menu with buttons
▲
and
▼
. Once the
parameter is selected, press the RESET button to make
it possible to change it using buttons
▲
and
▼
;
6.- Press the RESET button to save the changes;
7.- Wait for 10 seconds;
8 - Turn off electricity to the appliance;
9.- Turn electricity to the appliance back on to exit the
forced menu and return to normal operation.
18 - FORCED MENU