Comtrol WR7802-XT Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 128

background image

6 - R&TTE Directive 1999/5/EC

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

Introduction

Detailed specifications for the RocketLinx WR7802-XT Series are available on the Comtrol

.

R&TTE Directive 1999/5/EC

The product may be operated in all European Union countries. The R&TTE (1999/5/EC) Directive requires
that the apparatus bears the CE mark as conformation of compliance with the R&TTE Directive.

A formal declaration of R&TTE for wireless products is available on our web site. Different products may
conform to different standards of Health & Safety, EMC, Radio and other specific standards. You can
download the formal document for the product from the Web site or request it from our Sales/Technical staff.

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

FCC Caution

: Any changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate this equipment.

DHCP IP Range End

192.168.250.200

DHCP Subnet Mask

255.255.255.0

DHCP Gateway Address

192.168.250.1

Diagnostic CLI (Reserved for Engineering Diagnostics)

Console Type

3-pin (Tx, Rx, GND)

Baud Rate

115200

Cellular (3G/LTE)

SIM Socket

Default is SIM 1

Cellular Redundancy

Disabled by default. This feature is only available
when two SIM cards are inserted.

Cellular Connect

Automatically after the SIM is inserted and the
WR7802-XT is receiving power.

Others SIM Settings

Determined by your SIM card settings.

SIM Security

None

Features

Factory Default Settings

Beta

Version

«
...
6
7
8
9
10
...
»

Содержание WR7802-XT Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для WR7802-XT Series

Бренд: Cambium Networks Страницы: 29

Бренд: Paradyne Страницы: 2

Бренд: Vivotek Страницы: 136

ThunderLAN TNETE100A

Бренд: Texas Instruments Страницы: 179

Бренд: Justec Страницы: 61

SRA311-008P8 Series

Бренд: Divio Страницы: 4

IPS Pro-Module-24C-GE-BP-TM

Бренд: Trend Micro Страницы: 3

Бренд: Patton electronics Страницы: 2

Бренд: DIGIWEB Страницы: 16

Бренд: ZyXEL Communications Страницы: 3

Бренд: Goobay Страницы: 20

Wisenet PRN-6400DB4

Бренд: Hanwha Techwin Страницы: 125

DotSurfer GPC-2100

Бренд: Gtran Wireless Страницы: 44

Бренд: LevelOne Страницы: 4

Бренд: R.V.R. Elettronica Страницы: 171

Бренд: ADTRAN Страницы: 4

Бренд: ZyXEL Communications Страницы: 4

Бренд: Billion Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды