Comtrol WR7802-XT Series Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 128

background image

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

System | Relay Settings Page - 51

Configuration Using the Web User Interface

System | Relay Settings Page

Use the

Relay Settings

page to configure the DO relay.

Select the port or ports that want monitor for a link failure and then press

Apply

to activate the settings.

Note:

You must

Save

) settings, if you want to maintain these settings if the WR7802-XT is rebooted.

System | DDNS Settings Page

Use the

DDNS Settings

page to configure the parameters for DDNS (Dynamic Domain Name System) client.

Since not all carrier providers provide a fixed IP service and the dynamic IP address of Cellular interface may
change often, making it difficult to remotely manage the WR7802-XT’ IP address. Optionally, you can use
DDNS domain name instead fixed IP address.

Beta

Version

«
...
51
52
53
54
55
...
»

Содержание WR7802-XT Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для WR7802-XT Series

Бренд: D-Link Страницы: 11

Бренд: D-Link Страницы: 8

AirPlus DWL-810

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 84

INTERNET PRIVACY PROTECTION

Бренд: AlphaShield Страницы: 49

Бренд: Google Страницы: 14

Бренд: 3Com Страницы: 50

LMP-1202M-SFP Series

Бренд: ANTAIRA Страницы: 2

Бренд: IMC Networks Страницы: 36

Elinx EIR510 Series

Бренд: B&B Electronics Страницы: 2

Бренд: Casablanca Страницы: 13

Бренд: PairGain Страницы: 80

Dimension GS-2024

Бренд: ZyXEL Communications Страницы: 266

Бренд: Juniper Страницы: 9

Бренд: Belkin Страницы: 2

Бренд: Icy Box Страницы: 17

WSIL-1204-GT2-SFP2

Бренд: WAVESYS Страницы: 21

Бренд: Umniah Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды