Comtrol WR7802-XT Series Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 128

background image

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

Tools | Ping Page - 115

Configuration Using the Web User Interface

Tools | Ping Page

This feature allows you to check the status of remote station.

Enter the target IP address in the

Destination

field then press

Ping

.

The system pings the remote station four times and lists the ping results in the web GUI.

Note:

You must

Save

) settings, if you want to maintain these settings if the WR7802-XT is rebooted.

Save Page

Use this page to save configuration to flash. Every time you
finish changing the WR7802-XT configuration, you must save
the changes to flash if you want the changes to be permanent.

Logout Page

After you completed configuration and have saved the configuration (if
desired), you should logout the system.

If you do not log out of the system, the login session does not timeout for couple
minutes. There is a risk that other user may login the system without a
password. Another side affect is that you cannot access the WR7802-XT at the
same time if someone already login the system.

Use this page to logout. Press

Yes

to logout.

Reboot Page

Use this page to reboot the WR7802-XT.

Beta

Version

«
...
115
116
117
118
119
...
»

Содержание WR7802-XT Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для WR7802-XT Series

Бренд: 3Com Страницы: 20

Бренд: TDC Страницы: 27

Бренд: Accelerated Страницы: 10

Бренд: Accelerated Страницы: 4

Бренд: DBM Страницы: 50

OXTOPUS EIA-709

Бренд: OCCITALINA Страницы: 54

MediaStream ConnectPlus 1000

Бренд: Avid Technology Страницы: 74

Бренд: NETGEAR Страницы: 2

Бренд: TP-Link Страницы: 2

Бренд: Toto Link Страницы: 55

B-Control Fader BCF2000

Бренд: Behringer Страницы: 13

Бренд: HMS Страницы: 18

DGN2200M - Wireless-N 300 Router

Бренд: NETGEAR Страницы: 95

PowerTrans PT-7728

Бренд: Moxa Technologies Страницы: 8

Бренд: Lanner Страницы: 80

Бренд: Lanner Страницы: 116

Бренд: Umniah Страницы: 12

BiPAC 8200AXL-1200

Бренд: Billion Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды