Comtrol WR7802-XT Series Скачать руководство пользователя страница 86

Страница: 86 / 128

84 - Network Redundancy | Redundant Gateway Page

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

Configuration Using the Web User Interface

Note:

You must

Save

(

Page 115

) settings, if you want to maintain these settings if the WR7802-XT is rebooted.

Redundant Gateway

Status

Backup

Master

Backup

mode means that the Ring status is normal. If two links fail, the

Redundant Gateway function is triggered and it is changed to Master
mode.

Redundant gateway

You can

Enable

Disable

the Redundant Gateway function.

Gateway Address

Type the IP address of the main gateway of the Redundant Ring.

Ring ID

The redundant gateway checks the ring status of this Ring ID.

ARP Miss
Count(Default:5)

Type the number of ARP missed packets count.

When Ring status is abnormal, system transmits ARP packets in the
Ring to check whether the main gateway still alive or not. If the ARP
miss count is higher than the value that you set, the Redundant Gateway
status changes to

Master

and replaces the original gateway.

Beta

Version

Содержание WR7802-XT Series

































































































































Результаты поиска

Содержание WR7802-XT Series

Отзывы:

Похожие инструкции для WR7802-XT Series

Бренды по названию

Популярные бренды

Comtrol WR7802-XT Series, Руководство пользователя

Результаты поиска

Содержание WR7802-XT Series

Отзывы:

Похожие инструкции для WR7802-XT Series

Бренды по названию

Популярные бренды