Comtrol WR7802-XT Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 128

background image

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

Insert the SIM Card - 11

Hardware Installation

•

When the system is operational with a high gain antenna for short distance transmission, adjust the radio
output lower. Strong output power with a high gain antenna is not a proper installation method for short
distance transmission.

•

You are responsible for undertaking suitable lightning protection.

•

Install over-voltage protector devices on every outdoor Ethernet cable.

•

Protect each antenna installed outside with lightening protection devices, for example, a lightening
arrester.

Note: FIELD EMD (LIGHTNING) DAMAGE IS NOT COVERED UNDER WARRANTY.

Insert the SIM Card

The WR7802-XT provides dual external SIM (Subscriber Identity
Module) sockets to store the Cellular Nano SIM card. The WR7802-XT
only supports the Nano SIM card, which fits into the Nano SIM
carrier tray that slides into the SIM slots. The illustration shows the
types of SIM cards available.

If you want to use both SIM sockets, you should insert both SIM cards
into the WR7802-XT before applying power. After applying power, you
can enable the Cellular Redundant option and configure SIM 2 as
startup or backup SIM socket using the

Cellular Basic Settings

web

page.

Note:

The Cellular Redundant option is only available if you insert
two SIM cards into the sockets. If you only insert one, DO NOT
enable Cellular Redundant.

Use the following procedure to insert the SIM card.

Note:

The WR7802-XT cannot be powered on when inserting the SIM cards. Later when you power on the
WR7802-XT it takes approximately 1 minute to start up and searches for SIM card in SIM slot 1.

1.

Remove the two screws that secure the front plate of dual SIM socket.

2.

Remove the SIM carrier tray.

Note:

The SIM 1 is the default SIM socket.

3.

Place SIM card into the carrier, aligning the angled corner with the angled corner of the tray.

4.

Gently insert the SIM card into the SIM slot.

After completing the installation, if the Cellular connection is not connected, go to the

Status | Information

web page to check the Cellular status and settings.

Connect the Antenna

The WR7802-XT supports up to two antenna
sockets and two LTE antennas are shipped with the
product.

•

Antenna A is the LTE-Aux antenna

•

Antenna B is the LTE-Main antenna

Note:

Leave the dust cap on unconnected antennas.

The antennas shipped with the product are a wide-
temperature design; however, they are not water-
proof. If you want to install it in outdoor area, use
water-proof outdoor antennas.

Beta

Version

«
...
11
12
13
14
15
...
»

Содержание WR7802-XT Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для WR7802-XT Series

Бренд: H3C Страницы: 6

OfficeConnect 3CP4144

Бренд: 3Com Страницы: 4

OfficeConnect 3CP4144

Бренд: 3Com Страницы: 2

Бренд: H3C Страницы: 60

Бренд: H3C Страницы: 149

Бренд: 3Com Страницы: 27

OfficeConnect 3C19500

Бренд: 3Com Страницы: 52

Бренд: ADTRAN Страницы: 2

Бренд: H3C Страницы: 9

Бренд: Moxa Technologies Страницы: 36

S3000-EI Series

Бренд: Quidway Страницы: 16

DVI-Vision-IP-Fiber

Бренд: G&D Страницы: 240

Бренд: Planet Страницы: 2

Бренд: Watchguard Страницы: 21

Бренд: Extron electronics Страницы: 19

Бренд: Digital Equipment Страницы: 90

Modular Fast Fiber Switch Converter MT-RJ

Бренд: Lindy Страницы: 3

LOYTEC LIP‑3ECTC

Бренд: DELTA GROUP Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды