Comtrol WR7802-XT Series Скачать руководство пользователя страница 111

Страница: 111 / 128

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

Management | Login Settings Page - 109

Configuration Using the Web User Interface

Note:

You must

Save

(

Page 115

) settings, if you want to maintain these settings if the WR7802-XT is rebooted.

RADIUS

Use RADIUS (Remote Authentication Dial In User Service) account to
login to this device.

RADIUS --> Local

The RADIUS account or local account to login to this device. The
RADIUS account will be tried first.

TACPLUS

TACPLUS -->Local

RADIUS Server and Secondary RADIUS Server

RADIUS Server IP

Sets the IP address of an external RADIUS server as the authentication
database.

Shared Key

Sets specific characters for server authentication verification.

Server Port

Sets the communication port of an external RADIUS server as the
authentication database.

TACPLUS Authentication Setting

Authentication
Type

Choose the authentication protocol (ASCII/PAP/CHAP).

Authentication
Timeout

Set the length of time, in seconds, that the device waits for a response
from the primary server before sending the request to the secondary
server.

TACPLUS Server

TACPLUS Server IP

Sets the IP address of an external TACPLUS server as the
authentication database.

Shared Key

Sets specific characters for server authentication verification.

Server Port

Sets the communication port of an external TACPLUS server as the
authentication database.

Apply

Click the

Apply

button to apply the configuration changes.

Login Settings (Continued)

Beta

Version

Содержание WR7802-XT Series

































































































































Результаты поиска

Содержание WR7802-XT Series

Отзывы:

Похожие инструкции для WR7802-XT Series

Бренды по названию

Популярные бренды

Comtrol WR7802-XT Series, Руководство пользователя

Результаты поиска

Содержание WR7802-XT Series

Отзывы:

Похожие инструкции для WR7802-XT Series

Бренды по названию

Популярные бренды