Comtrol WR7802-XT Series Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 128

background image

RocketLinx WR7802-XT Series User Guide

: 2000638 Rev. A

Network Redundancy | Redundant Gateway Page - 83

Configuration Using the Web User Interface

Network Redundancy | Redundant Gateway Page

Redundant Gateway is a Ring redundancy feature that you can implement for backup if two links fail in a
Ring.

In the images above, the Redundant Ring, IP:192.168.11.1 is the main gateway, and there are other devices in
the same ring which provides a Cellular interface for external network transmission.

If there are two link failures, this would mean that the other devices cannot transmit data to the external
network. You would manually need to change the settings on each device to recover external access.

To solve this problem, you can use the

Redundant Gateway

. If two links fail, the Redundant Gateway device

creates an internal virtual gateway (the same as original main gateway) so for other devices, the main
gateway still exists and these devices can transmit data to external network via Cellular interface of the
Redundant Gateway device.

Beta

Version

«
...
83
84
85
86
87
...
»

Содержание WR7802-XT Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для WR7802-XT Series

Бренд: Icidu Страницы: 10

Бренд: Paradyne Страницы: 2

Бренд: Pakedge Device & Software Страницы: 20

Бренд: Yamaha Страницы: 24

Бренд: Yamaha Страницы: 5

Бренд: ZyXEL Communications Страницы: 2

PSoC 4 S Series

Бренд: Cypress Страницы: 4

McDATA Eclipse 1620

Бренд: Sun Microsystems Страницы: 9

ControlCenter-IP 2.0

Бренд: G&D Страницы: 60

Бренд: H3C Страницы: 4

Бренд: qpcom Страницы: 4

Бренд: IBM Страницы: 288

Бренд: Cisco Страницы: 122

Бренд: Technicolor Delivery Technologies Страницы: 76

SIMATIC NET RUGGEDCOM RX1500

Бренд: Siemens Страницы: 66

Бренд: Siemens Страницы: 72

SIMATIC NET CP 343-1

Бренд: Siemens Страницы: 78

Бренд: Siemens Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды