Compaq ML570 - ProLiant - 1 GB RAM Скачать руководство пользователя страница 96

Страница: 96 / 204

Error messages 96

Accelerator Status: Warranty Alert

Description

: Catastrophic problem exists with array accelerator board. Refer to other messages on

Diagnostics screen for exact meaning of this message.

Action

: Replace the array accelerator board.

Adapter/NVRAM ID Mismatch

Description

: EISA NVRAM has an ID for a different controller from the one physically present in the slot.

Action

: Run the server setup utility.

Array Accelerator Battery Pack X not Fully Charged

Description

: Battery is not fully charged.

Action

: If 75% of the batteries present are fully charged, the array accelerator is fully operational. If more

than 75% of the batteries are

not

fully charged, allow 36 hours to recharge them.

Array Accelerator Battery Pack X Below Reference Voltage (Recharging)

Description

: Battery pack on the array accelerator is below the required voltage levels.

Action

: Replace the array accelerator board if the batteries do not recharge within 36 powered-on hours.

Board in Use by Expand Operation

Description

: Array accelerator memory is in use by a capacity expansion or RAID migration.

Action

: The array accelerator is automatically re-enabled for caching when the capacity expansion or RAID

operation completes.

Board not Attached

Description

: An array controller is configured for use with array accelerator board, but one is not connected.

Action

: Connect array accelerator board to array controller.

Cache Has Been Disabled Because ADG Enabler Dongle is Broken or Missing

Description

: The cache has been disabled because RAID ADG volume is configured but the ADG Enabler

Dongle is broken or missing.

Action

: Check the ADG Enabler Dongle. Replace if needed.

Cache Has Been Disabled; Likely Caused By a Loose Pin on One of the RAM Chips

Description

: Cache has been disabled due to a large number of ECC errors detected while testing the cache

during POST. This is probably caused by a loose pin on one of the RAM chips.

Action

: Try reseating the cache to the controller. If that does not work, replace the cache.

Содержание ML570 - ProLiant - 1 GB RAM













































































































































































































Результаты поиска

Содержание ML570 - ProLiant - 1 GB RAM

Отзывы:

Похожие инструкции для ML570 - ProLiant - 1 GB RAM

Бренды по названию

Популярные бренды

Compaq ML570 - ProLiant - 1 GB RAM, Руководство по устранению неисправностей

Результаты поиска

Содержание ML570 - ProLiant - 1 GB RAM

Отзывы:

Похожие инструкции для ML570 - ProLiant - 1 GB RAM

Бренды по названию

Популярные бренды