Compaq ML570 - ProLiant - 1 GB RAM Скачать руководство пользователя страница 154 | Manualshive

Страница: 154 / 204

background image

Error messages 154

1730-Fixed Disk 0 Does Not Support DMA Mode

Audible Beeps

: None

Possible Cause

: Fixed drive error detected.

Action

: Run the server setup utility and correct the configuration.

1731-Fixed Disk 1 Does Not Support DMA Mode

Audible Beeps

: None

Possible Cause

: Fixed drive error detected.

Action

: Run the server setup utility and correct the configuration.

1732-Slot X Drive Array - Array Accelerator Battery Pack Missing...

...Array Accelerator Posted-Write Cache is disabled until additional battery packs are installed.

Audible Beeps

: None

Possible Cause

: Battery packs are detached from the controller or have failed.

Action

: Check the battery pack to be sure the connection is secure. If the condition persists, then install a

replacement battery pack.

1733-Slot X Drive Array - Storage Enclosure Firmware Upgrade Problem Detected...

...Port x Box y

(Followed by one of the following:)
*Enclosure firmware upgrade needed - run Flash Components.
*Unable to read firmware version of one or more components

Audible Beeps

: None

Possible Cause

: An incorrect enclosure firmware version is installed, or an enclosure firmware upgrade is

needed.

Action

:

•

Upgrade the enclosure firmware and the controller firmware.

•

If the condition persists, then replace the enclosure components.

For more information, see the HP BladeSystem c-Class Enclosure Troubleshooting Guide on the HP website
(

http://www.hp.com/support/BladeSystem_Enclosure_TSG_en

).

1735-Slot X Drive Array - Unsupported Redundant Cabling Configuration Detected...

...Multiple paths to the same enclosure/drives are not supported by this Smart Array firmware version. Access to all
drives has been disabled until redundant SAS cable(s) are detached, or firmware is updated to a version that supports

dual-domain.

Audible Beeps

: None

Possible Cause

: An unsupported redundant cabling configuration for the Smart Array firmware version is

installed.

Action

: Disconnect the redundant SAS cables, and then update the Smart Array firmware to the correct

version.

«
...
152
153
154
155
156
...
»

Содержание ML570 - ProLiant - 1 GB RAM













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ML570 - ProLiant - 1 GB RAM

Бренд: GE Страницы: 6

Бренд: ZALMAN Страницы: 20

Бренд: Keithley Страницы: 59

Бренд: Qlogic Страницы: 2

Super Sound Set SR-JV80-07

Бренд: Roland Страницы: 8

Бренд: Schrack Technik Страницы: 2

Бренд: Moxa Technologies Страницы: 2

Бренд: ADTRAN Страницы: 2

Бренд: Xantech Страницы: 4

Бренд: Renesas Страницы: 746

Бренд: TRENDnet Страницы: 12

Bluespoon 17-1000

Бренд: Radio Shack Страницы: 1

Бренд: 3Com Страницы: 12

MP5S Plus Writer

Бренд: SONIX Страницы: 23

Бренд: Kontron Страницы: 32

Бренд: Avigilon Страницы: 12

Бренд: Transition Networks Страницы: 1

Бренд: SMC Sierra Monitor Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды