ComAp InteliLite NT AMF Series Скачать руководство пользователя

Страница: 51 / 84

InteliLite

– AMF20/25, SW version 1.2, ©ComAp – March 2008

IL-NT-AMF-Reference Guide1.2.pdf

Mains

VUnb

Del

[s]

Delay for mains voltage unbalance
Step:

0.1 s

Range:

0- 60.0

Mains >Freq

[%]

Threshold for mains overfrequency. All three phases are checked. Maximum out of three is used.
Step:

0.1% of Nominal frequency

Range:

50 (Mains <Freq) – 150.0%

Mains <Freq

[%]

Threshold for mains underfrequency. All three phases are checked. Maximum out of three is used.
Step:

0.1% of Nominal frequency

Range:

50% – 150.0(Mains >Freq)%

Mains Freq Del

[s]

Delay for mains underfrequency and overfrequency
Step:

0.1s

Range:

0 – 60.0 s

MCB Logic

[CLOSE-ON / CLOSE-OFF]

The set point influences the behavior of the output MCB CLOSE/OPEN
CLOSE-ON: When the output MCB CLOSE/OPEN is closed – MCB should be closed.
CLOSE-OFF: When the output MCB CLOSE/OPEN is closed – MCB should be opened.

iL “OFF”

MCB logic = ”CLOSE-ON”

iL “ON

”

Mains O.K.

Mains Failure

Signal after external
inverted relay

MCB logic = ”CLOSE-OFF”

Battery

DO 4

MCB

AUX.

INVERTING

RELAY

Содержание InteliLite NT AMF Series





















































































Результаты поиска

Содержание InteliLite NT AMF Series

Отзывы:

Похожие инструкции для InteliLite NT AMF Series

Бренды по названию

Популярные бренды

ComAp InteliLite NT AMF Series, Справочное руководство

Результаты поиска

Содержание InteliLite NT AMF Series

Отзывы:

Похожие инструкции для InteliLite NT AMF Series

Бренды по названию

Популярные бренды