ComAp InteliLite NT AMF Series Скачать руководство пользователя

Страница: 23 / 84

InteliLite

– AMF20/25, SW version 1.2, ©ComAp – March 2008

IL-NT-AMF-Reference Guide1.2.pdf

COM L1l

K L

k l

L2l

L3l

Set points adjustment

To run a single-phase application, the following set points have to be set:

Gener Protect

Amps Unbal Sd

to 200 %

Gener Protect

Amps Unbal Del

to 60,0 s

Analog inputs

Three analog inputs are available on the IL-NT

Configuration

Each analog input can be configured by LiteEdit software following way.

Analog input item

LiteEdit

Possibility

Type Type

Not

used

Alarm

Analog input isn’t used

Analog input name

Name

Up to 14 ASCII characters

Config of input

Config

Analog

Binary (not supp. by PTM)
Tri-state (not supp. by PTM)

ECU

Analog measuring in specified
range.
Binary: open/close - threshold
750

Three-state: open/close -
threshold 750

Failure <10

or > 2400

Value is read from ECU

Physical dimension

Dim

bar,%,°C, …

Up to 3 ASCII characters
(Valid only for analog inputs)

Polarity Contact

type

NC

NO

Valid only for binary and three-
state inputs
Valid only for binary and three-
state inputs

Over

Overstep. Sensor fail does not
activate protection.

Over+Fls

Overstep and Sensor fail
activates protection.

Under

Under step. Sensor fail does
not activate protection.

Protection direction

Protection

Under+Fls

Under step and Sensor fail
activates protection.

Sensor characteristic Sensor

Predefined user curves

User changeable and
configurable

Decimal points

Dec

0, 1, 2

Number of decimal points
(Valid only for analog inputs)

Each Analog input has separate set points for two level alarm setting. Analog input alarm levels and
delay adjust in

Engine Protect

group.

Содержание InteliLite NT AMF Series





















































































Результаты поиска

Содержание InteliLite NT AMF Series

Отзывы:

Похожие инструкции для InteliLite NT AMF Series

Бренды по названию

Популярные бренды

ComAp InteliLite NT AMF Series, Справочное руководство

Результаты поиска

Содержание InteliLite NT AMF Series

Отзывы:

Похожие инструкции для InteliLite NT AMF Series

Бренды по названию

Популярные бренды