ComAp InteliLite NT AMF Series Скачать руководство пользователя

Страница: 71 / 84

InteliLite

– AMF20/25, SW version 1.2, ©ComAp – March 2008

IL-NT-AMF-Reference Guide1.2.pdf

Events specification

Protection

type

Information on binary
output available (See

list of

Binary outputs

)

Description

Sd BatteryFlat

YES

If the controller switches off during
starting sequence due to bad battery
condition it doesn’t try to start again
and activates this protection.

Sd Start Fail

YES

Gen-set start failed.

ParamFail

NONE

Wrong checksum of parameters.
Happends typically after downloading
new firmware or changing of the
parameter. The controller stays in
INIT mode. Check all parameters,
write at least one new parameter.

Sd Gen Lx >,<V

YES

The generator voltage is out of limits
given by

Gen <V Sd

and

Gen >V Sd

setpoints.

Sd Gen V Unbal

YES

The generator voltage is unbalanced
more than the value of

Volt Unbal Sd

setpoint.

Sd Gen >Freq

YES

The generator frequency is out of
limits given by

Gen >Freq Sd

and

Gen

<Freq Sd

setpoints.

Wrn Amps Unbal

The generator current is unbalanced.

Sd Overload

YES

The load is greater than the value
given by

Overload

setpoint.

Sd Overspeed

YES

The protection comes active if the
speed is greater than

Overspeed

setpoint.

Sd Underspeed

YES

During starting of the engine when the
RPM reach the value of

Starting RPM

setpoint the starter is switched off and
the speed of the engine can drop
under

Starting RPM

again. Then the

Underspeed protection becomes
active. Protection evaluation starts 5
seconds after reaching

StartingRPM

EmergencyStop

If the input

Emergency Stop

is opened

shutdown is immediately activated.

GCB Fail

Failure of generator circuit breaker.

MCB Fail

Failure of mains circuit breaker.

RPM Meas Fail

Failure of magnetic pick-up sensor for
speed measurement.

Sd Stop Fail

YES

Gen-set stop failed.

WrnMaintenance WRN

The

period for servicing is set by the

Maintenance

setpoint. The protection

comes active if the running hours of
the engine reach this value.

ChargeAlt Fail

WRN

YES

Failure of alternator for charging the
battery.

Sd Override

WRN

The protection is active if the output

Sd Override

is closed.

*Wrn RA15 Fail

WRN

Warning alarm in case of lost
connection to IGL-RA15 module.

*Sd IOM Fail

Shutdown alarm in case of lost
connection to IG-IOM/IGS-PTM
module.

Wrn ECU Alarm

WRN

ECU alarm list is not empty

Low BackupBatt

WRN

RTC backup battery is flat

Содержание InteliLite NT AMF Series





















































































Результаты поиска

Содержание InteliLite NT AMF Series

Отзывы:

Похожие инструкции для InteliLite NT AMF Series

Бренды по названию

Популярные бренды

ComAp InteliLite NT AMF Series, Справочное руководство

Результаты поиска

Содержание InteliLite NT AMF Series

Отзывы:

Похожие инструкции для InteliLite NT AMF Series

Бренды по названию

Популярные бренды