ComAp InteliLite NT AMF Series Скачать руководство пользователя

Страница: 64 / 84

InteliLite

– AMF20/25, SW version 1.2, ©ComAp – March 2008

IL-NT-AMF-Reference Guide1.2.pdf

AUT Mode

The controller does not respond to buttons START, STOP, MCB ON/OFF, GCB ON/OFF. Engine
start/stop request is evaluated form Mains failure/return.

AMF sequence (simplified)

State

Condition of the transition

Action

Next state

Mains failed

or MCB feedback dropout

MCB Opens On

= MAINSFAIL

MCB CLOSE/OPEN off

EmergStart Del

timer

started

Mains failure

Mains
operation

Mains failed

or MCB feedback dropout

MCB Opens On

= GENRUN

EmergStart Del

timer

started

Mains failure

Mains voltage and frequency OK

MCB Opens On

= MAINSFAIL

After elapsing

MCB Close

Del

MCB CLOSE/OPEN

Mains operation

Mains voltage and frequency OK

MCB Opens On

= GENRUN

None

Mains operation

EmergStart Del

elapsed

MCB Opens On

= MAINSFAIL

Engine start sequence
performed, then
GCB CLOSE/OPEN on

Island operation

Mains
failure

EmergStart Del

elapsed

MCB Opens On

= GENRUN

Engine start sequence
performed, then MCB
CLOSE/OPEN off, time
delay

Fwd Return Del

performed and GCB
CLOSE/OPEN on

Island operation

Island
operation

Mains voltage and frequency OK

MainsReturnDel

timer

started

Mains return

Mains failed

Island operation

Mains
return

MainsReturnDel

elapsed

GCB CLOSE/OPEN off,
then after

Fwd Return Del

MCB CLOSE/OPEN on
and then engine stop
sequence performed

Mains operation

Mains failed

means mains over/under -voltage, over/under -frequency, voltage assymetry (preset

delay must elapse)

If during start-up sequence mains returns, then MCB is reclosed with delay

MCB Close Del (

opened, depending on

MCB Opens On

setpoint) and start-up sequence is interrupted.

If mains fails during stop procedure (cooling) again, stop sequence is interrupted, MCB opened and

GCB reclosedclosed with delay

Fwd Return Del.

Содержание InteliLite NT AMF Series





















































































Результаты поиска

Содержание InteliLite NT AMF Series

Отзывы:

Похожие инструкции для InteliLite NT AMF Series

Бренды по названию

Популярные бренды

ComAp InteliLite NT AMF Series, Справочное руководство

Результаты поиска

Содержание InteliLite NT AMF Series

Отзывы:

Похожие инструкции для InteliLite NT AMF Series

Бренды по названию

Популярные бренды