ComAp InteliDrive DCU Marine Скачать руководство пользователя страница 90

Страница: 90 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

In configuration window you can assign one of three passwords. It is necessary to enter correct password. If

password does not exists, user is asked to create it.

IMPORTANT: Very important parts of the control algorithm must not be locked in PLC sheets.

Certification authorities may request their unlocking if necessary.

5.2 Shared IO and Virtual IO

5.2.1 Virtual Binary Outputs (VBOUT) module

Several virtual modules are available. One of them is Virtual Binary Outputs module (VBOUT)

which enables use of Prg. states binary signals with the built-in PLC. Prg. states signal can not be directly

configured as a PLC module input. Therefore it is necessary to use VBOUT module as interface between a Prg.

state signal and a PLC module.

Up to 4 VBOUT modules are available, each VBOUT modules represents 8 binary output signals.

5.2.2 Shared virtual inputs and outputs

It is possible to share Binary and Analog values between all the controllers via CAN bus, thus saving physical

Inputs and Outputs and excess wiring.

How to add a virtual module is shown in the following picture.

Содержание InteliDrive DCU Marine






























































































































































































































































































Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы:

ComAp InteliDrive DCU Marine, Руководство пользователя, Страница: 90 / 285

Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы: