ComAp InteliDrive DCU Marine Скачать руководство пользователя страница 76

Страница: 76 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

4.4.10 I-CB Communication bridge

Image 4.14 Dimensions of I-CB

All dimensions are in mm.

I-CB unit can be mounted on DIN rail (35 mm).

I-CB (Communication bridge) is CAN bus interface between Controller and Engine Control Unit (ECU)

that has not standard J1939 communication (MTU, CAT etc.). Engine values (RPM, Oil pressure and

other) are received from ECU via CAN and corresponding sensors are not needed on controller. Use

ICBEdit software for I-CB configuration (included in installation package).

I-CB wiring and configuration

1. Configure I-CB using I-CBEdit software. Configured I-CB behaves like fictive IS-AIN and IS-BIN units. I-CB

configuration associates selected values (from ECU database) received from Engine Control Unit to

selected CAN addressees (fictive IS-AIN, IS-BIN inputs and outputs).

2. Configure corresponding controller CAN addresses and tick in PC configuration tool.

3. Configure separate inputs and outputs in corresponding Analog, Binary inputs, outputs in PC configuration

tool.

Note:

In case of CAT engines, there is RS232 connection between I-CB and CCM.

4.4.11 I-AOUT8

General Description

I-AOUT8 is an extension unit with 8 Analog outputs. Each analog output can be switched by jumper for.

Содержание InteliDrive DCU Marine






























































































































































































































































































Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы:

ComAp InteliDrive DCU Marine, Руководство пользователя, Страница: 76 / 285

Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы: