ComAp InteliDrive DCU Marine Скачать руководство пользователя страница 61

Страница: 61 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

4.3.8 Connection of ID-DCU MARINE analog inputs

Standard connection of resistive sensors to ID-

DCU MARINE analog inputs AI1 to AI8. The COM

terminal must be always connected to the negative

power terminal.

Different sensors connection to ID-DCU MARINE.

AI configuration jumpers must be in corresponding

position and corresponding DriveConfig

configuration according to used sensor.

Analog input common terminal COM has to be

connected to ID minus Power supply terminal.

Mixed connection of ID-DCU MARINE analog

inputs:

AI2, AI7 - current sensor

AI1, AI5 - resistive sensor

AI3, AI8 - voltage input

AI6- thermocouple (voltage)

AI4 - Not used

Mixed connection of InteliDrive analog inputs:

AI1, AI2, AI5, AI6 - resistive sensor

AI3, AI7 - binary input

AI4, AI8 - three state input

Analog input common terminal COM has to be

connected to ID minus Power supply terminal.

To ensure a proper function use shielded cables, especially for length over >3 m.

4.3.9 ID-DCU MARINE Analog inputs hardware configuration

Configure Analog inputs AI1-AI8 connection by jumpers on PCB (remove cover).

Содержание InteliDrive DCU Marine






























































































































































































































































































Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы:

ComAp InteliDrive DCU Marine, Руководство пользователя, Страница: 61 / 285

Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы: