ComAp InteliDrive DCU Marine Скачать руководство пользователя страница 17

Страница: 17 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

3. Press

Enter

to confirm.

4. Use ↑ or ↓ to select requested set point.

5. Set points marked “

” are password protected.

6. Press

Enter

to edit.

7. Use

↑

↓

to modify the set point. When

↑

↓

is pressed for 2 sec, auto repeat function is activated.

8. Press

Enter

to confirm or

Page

to leave without change.

9. Press

Page

to leave selected set points group.

2.1.11 How to view measured data?

Pressing the

Page

button repeatedly will scroll the user through the menu screens. Select the

MEASUREMENT screen. Use

↑

and

↓

to select the screen with requested data.

2.1.12 How to view the History menu?

1. Pressing the

Page

button repeatedly will scroll the user through the menu screens. Select the HISTORY

screen.

2. Use ↑ or ↓ to select a requested record.

3. Use

Enter

to select requested screen (record items) within displayed records

2.1.13 Main screen indication

Active controller mode (inverse)

Available mode

Controller

LOC

(Local) mode indication

= Remote connection indication (connection to InteliMonitor is active)

= Access lock indication

Содержание InteliDrive DCU Marine






























































































































































































































































































Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы:

ComAp InteliDrive DCU Marine, Руководство пользователя, Страница: 17 / 285

Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы: