ComAp InteliDrive DCU Marine Скачать руководство пользователя страница 284

Страница: 284 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

284

Analog output (values) configuration

Any of values from the Source list can be configured to any physical or ECU/J1939 (virtual) Analog output.

Module

Number of outputs

Note

ID-SCM

10V or 20mA or 10V/10kΩ

IGS-PTM

10V or 20mA

I-AOUT8

10V or 20mA or pwm

I-IO8/8

20mA (10V or pwm not supported by ID-DCU Marine 2.2)

ECU (J1939)

4 (virtual)

Format depends on ECU

Analog outputs availability

Analog output configuration

It is possible to convert Source analog value by linear interpolation (conversion). The conversion is given by

definition of two points, Low and High one.

Following is example of transfer characteristics 0 - 100% to 0 – 20mA.

Following are examples of transfer characteristics 0 - 100% to 4 – 20mA. The first case is transfer

characteristics -25 - 100% to 0 – 20mA, it contains the needed conversion to 4 – 20mA.

Содержание InteliDrive DCU Marine






























































































































































































































































































Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы:

ComAp InteliDrive DCU Marine, Руководство пользователя, Страница: 284 / 285

Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы: