ComAp InteliDrive DCU Marine Скачать руководство пользователя страница 174

Страница: 174 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

174

Protections

Protection group contains all Analog inputs and Binary inputs protection limits and delays. List is dynamically

created during configuration process.

8.1.3 Binary Inputs

Any InteliDrive controller extension physical binary input can be configured as “function” or “protection”.

Following chapter contains Logical binary inputs list that can be configured to any physical input.

ID-DCU MARINE binary inputs

Remote Start, Remote Stop, Rem Start/Stop

are not active in LOC (local)

mode.

Note:

Minimal input pulse duration is 120 ms to be detected as valid (binary inputs sampling rate is 100 ms).

Adjustable delay can be configured to any binary input when is used as a protection: Standard = 0,5 sec or one

of BinInp delay 1, 2, 3 that can be adjusted by corresponding Setpoint BinInp Delay 1, 2, 3.

Input

BI delay configuration

Setpoint

Standard (0,5s)

BinInp delay 1

BinInp Delay 1

BinInp delay 2

BinInp Delay 2

BinInp delay 3

BinInp Delay 3

See setpoints BinInp delay 1 [s] etc…

Содержание InteliDrive DCU Marine






























































































































































































































































































Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы:

ComAp InteliDrive DCU Marine, Руководство пользователя, Страница: 174 / 285

Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы: