ComAp InteliDrive DCU Marine Скачать руководство пользователя страница 203

Страница: 203 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

203

Related FW

3.0.0

Related applications

All

Comm object

1461

Description

The first press of

0/1

- panel Close Load button activates the new LBO

ClutchBtToggle

, the second press

deactivates it, The function operates in all engine modes and states and can be used for some independent

PLC function when standard Clutch function is not used.

Existing function of pnael Close load button

0/1

(LBO Close Load) is without change.

Close Load function works for remote access from DriveMonitor, Modbus, Modem, ... as well.

ClutchBtToggle

back to List of LBO

Related FW

3.0.0

Related applications

All

Comm object

Description

The output closes during engine start, after Idle time setpoint elapses. The output opens again after Cooling

time is finished. The opposite logic output Nominal/Idle is available as well.

Note:

Connect Binary output Idle/Nominal to electronic speed governor to switch the speed: opened =

IDLE, closed=RATED.

Idle/Nominal

back to List of LBO

Related FW

3.0.0

Related applications

All

Comm object

1373

Description

Indicates High Exhaust System Temperature (HEST). It may be active during DPF regeneration to indicate

higher than normal exhaust temperatures.

HEST Lamp

back to List of LBO

Related FW

3.0.0

Related applications

All

Comm object

Description

Closed output energizes the engine starter.

Starter

back to List of LBO

Related FW

3.0.0

Related applications

All

Comm object

Description

Output is closed during engine stopping procedure.

Stop Solenoid

back to List of LBO

Содержание InteliDrive DCU Marine






























































































































































































































































































Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы:

ComAp InteliDrive DCU Marine, Руководство пользователя, Страница: 203 / 285

Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы: