ComAp InteliDrive DCU Marine Скачать руководство пользователя страница 20

Страница: 20 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

2.2.4 DriveConfig

Standard installation pack contains following controller file types:

Firmware

Application file (archive)

ID-DCU-MARINE-3.0.0.mhx

DCU-MARINE-AUX-3.0.0.aid

DCU-MARINE-EME-3.0.0.aid

DCU-MARINE-CMB-3.0.0.aid

DCU-MARINE-PRP-3.0.0.aid

Delivered controller contains firmware and default configuration. Any Application file can be modified by

customer using DriveConfig PC software. It is possible to download Application file from the controller, modify it

and download back. There must be corresponding version of Application file with firmware in controller.

Note:

Configuration aid file does not contain the History record when had been read from the InteliDrive

controller by DriveConfig.

Note:

To load History file from InteliDrive use InteliMonitor software only.

Application file - archive

There exists one binary type of configuration file only. Config file “*.aid” contains:

Complete I/O configuration (include extension modules if any)

Setpoints setting

All available languages

Configuration file can be opened (Open file or Load from ID) modified and stored to the PC (Save, Save as) or

downloaded to Controller (Store to ID).

DriveConfig functions

Tool for ID-DCU MARINE controller and extension modules configuration

Extension modules addressing

All I/O function or protection configuration

Setpoints adjusting

Содержание InteliDrive DCU Marine






























































































































































































































































































Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы:

ComAp InteliDrive DCU Marine, Руководство пользователя, Страница: 20 / 285

Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы: