Citrix NetScaler EE, Руководство по установке и настройке

Страница: 833 / 1026

© 1999-2017 Citrix Systems, Inc. All rights reserved. p.833 https://docs.citrix.com
Connecting the Cables
Jun 12, 2014
When the appliance is securely mounted on the rack, determine which ports you should use. You are then ready to connect
the cables. Ethernet cables and the optional console cable are connected first. Connect the power cable last.
Warning: Before installing or repairing the appliance, remove all jewelry and other metal objects that might come in contact
with power sources or wires. When you touch both a live power source or wire and ground, any metal objects can heat up
rapidly and cause burns, set clothing on fire, or fuse the metal object to an exposed terminal.
Port s
Port s
A typical installation using a single accelerated bridge uses four Ethernet ports (the Primary port and apA) and six IP
addresses (four on the Primary port's subnet and two on apA's subnet).
The appliance has two motherboard ports and two accelerated bridges.
The motherboard ports are labeled as MGMT (management) and AUX1 (auxiliary) ports in SD-WAN 1000-SE appliance
and PRI (primary) and AUX (auxiliary) in SD-WAN 2000-SE appliance. You use MGMT port of the SD-WAN 1000-SE
appliance and PRI port of the SD-WAN 2000-SE appliance for initial configuration.
Accelerated bridge ports are apA and apB are available on the back panel of SD-WAN 1000-SE appliance and the front
panel of SD-WAN 2000-SE appliance. On 1000-SE appliance, these ports are labeled as LAN1 and WAN1, and LAN2 and
WAN2, respectively. However, on 2000-SE appliance, these ports are labeled as 1/1 and 1/2, and 1/3 and 1/4, respectively.
Connect ing t he Et hernet Cables Connect ing t he Et hernet Cables
Ethernet cables connect your appliance to the network. The type of cable you need depends on the type of port used to
connect to the network. Use a category 5e or category 6 Ethernet cable with a standard RJ-45 connector on a
10/100/1000BASE-T port.
T o connect an Et hernet cable t o a 10/100/1000BASE-T port
T o connect an Et hernet cable t o a 10/100/1000BASE-T port
1. Insert the RJ-45 connector on one end of your Ethernet cable into an appropriate port.
On 1000-SE 1000-SE appliance, the ports are available on the back panel and labeled as LAN1 and WAN1 for apA bridged port for
LAN and WAN links, respectively.
On 2000-SE 2000-SE appliance, the ports are available on the front panel. The ports are labeled as 1/1 and 1/2 for the apA
bridged port. You can use 1/1 for LAN and 1/2 for WAN link.
2. Insert the RJ-45 connector on the other end into the target device, such as a router or switch.
3. Verify that the LED glows amber when the connection is established.
Connect ing t he Console Cable Connect ing t he Console Cable
You can use the console cable to connect your appliance to a computer or terminal, from which you can configure the
appliance. Before connecting the console cable, configure the computer or terminal to support VT100 terminal emulation,
9600 baud, 8 data bits, 1 stop bit, parity, and flow control set to NONE. Then connect one end of the console cable to the
RS232 serial port on the appliance and the other end to the computer or terminal.
T o connect t he console cable t o a comput er or t erminal
T o connect t he console cable t o a comput er or t erminal
1. Insert the DB-9 connector at the end of the cable into the console port.
On 1000-SE 1000-SE appliance, the port is located on the back panel.
On 2000-SE 2000-SE appliance, the port is located on the front panel.