background image

Page 2

WARRANTY

The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from

defects in material or workmanship for a period of one (1) year from the date of sale thereof to an original purchaser for

use, except as hereinafter provided. With respect to non-durable parts normally requiring replacement in less than one (1)

year due to normal wear and tear, including, but not limited to, cloth goods, valve discs, hoses, and iron cords, and with

respect to all new repair or replacement parts for Cissell equipment for which the one (1) year warranty period has expired,

or for all new repair or replacement parts for equipment other than Cissell equipment, the warranty period is limited to

ninety (90) days from date of sale. The warranty period on each new replacement part furnished by Cissell in fulfillment

of the warranty on new equipment or parts shall be for the unexpired portion of the original warranty period on the part

replaced.

With respect to electric motors, coin meters and other accessories furnished with the new equipment, but not manufactured

by Cissell, the warranty is limited to that provided by the respective manufacturer.

Cissell's total liability arising out of the manufacture and sale of new equipment and parts, whether under the warranty or

caused by Cissell's negligence or otherwise, shall be limited to Cissell repairing or replacing, at its option, any defective

equipment or part returned f.o.b. Cissell's factory, transportation prepaid, within the applicable warranty period and found

by Cissell to have been defective, and in no event shall Cissell be liable for damages of any kind, whether for any injury to

persons or property or for any special or consequential damages. The liability of Cissell does not include furnishing (or

paying for) any labor such as that required to service, remove or install; to diagnose troubles; to adjust, remove or replace

defective equipment or a part; nor does it include any responsibility for transportation expense which is involved therein.

The warranty of Cissell is contingent upon installation and use of its equipment under normal operating conditions. The

warranty is void on equipment or parts; that have been subjected to misuse, accident, or negligent damage; operated under

loads, pressures, speeds, electrical connections, plumbing, or conditions other than those specified by Cissell; operated

or repaired with other than genuine Cissell replacement parts; damaged by fire, flood, vandalism, or such other causes

beyond the control of Cissell; altered or repaired in any way that effects the reliability or detracts from its performance,

or; which have had the identification plate, or serial number, altered, defaced, or removed.

No defective equipment or part may be returned to Cissell for repair or replacement without prior written authorization

from Cissell. Charges for unauthorized repairs will not be accepted or paid by Cissell.

CISSELL MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY, STATUTORY OR OTHERWISE, CONCERNING

THE EQUIPMENT OR PARTS INCLUDING, WITHOUT LIMITATION, A WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE, OR A WARRANTY OF MERCHANTABILITY. THE WARRANTIES GIVEN ABOVE ARE EXPRESSLY IN

LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. CISSELL NEITHER ASSUMES, NOR AUTHORIZES

ANY PERSON TO ASSUME FOR IT, ANY OTHER WARRANTY OR LIABILITY IN CONNECTION WITH THE
MANUFACTURE, USE OR SALE OF ITS EQUIPMENT OR PARTS.

For warranty service, contact the Distributor from whom the Cissell equipment or part was purchased. If the Distributor
cannot be reached, contact Cissell.

Содержание FFCD


































Отзывы: