manualshive.com logo in svg

Cisco CiscoWorks WLSE 1130-19, Руководство по установке и настройке

Поделиться
Скачать
Cisco CiscoWorks WLSE 1130-19 Скачать руководство пользователя страница 79

4-3

Installation and Configuration Guide for the CiscoWorks Wireless LAN Solution Engine

78-16778-01

Chapter 4      Setting Up Devices—Overview

    About Device Setup Methods

Configuring Non-IOS Access Points and Bridges

You can use the device Web interface or a WLSE configuration template to 
configure non-IOS devices.

Device configuration consists of:

•

Normally, enabling Cisco Discovery Protocol (CDP)

•

Configuring SNMP

•

Adding an HTTP user and enabling the User Manager

•

Normally, selecting TFTP as the transfer protocol between APs and the 
WLSE

Configuring IOS Access Points and Bridges

You can use the device Web interface, the device CLI, or WLSE configuration 
templates to configure IOS devices.

Device configuration consists of:

•

Basic network configuration:

–

Normally, enabling Cisco Discovery Protocol (CDP)

–

Configuring SNMP

–

Configuring Telnet or SSH for pushing configuration to APs

•

Radio management configuration:

–

Configuring Wireless Domain Services (WDS) devices—either APs or 
Wireless LAN Services Modules (WLSMs)

–

Configuring infrastructure APs to authenticate to WDS

Configuring Routers and Switches

Note

Only routers and switches that have properly configured access points or bridges 
attached to them will be discovered.

Router and switch configuration consists of:

•

Enabling Cisco Discovery Protocol (CDP)

Содержание CiscoWorks WLSE 1130-19









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды