Cisco CiscoWorks WLSE 1130-19 Скачать руководство пользователя страница 65

Страница: 65 / 104

3-3

Installation and Configuration Guide for the CiscoWorks Wireless LAN Solution Engine

78-16778-01

Chapter 3 Setting Up the WLSE

Configuring the WLSE’s Network Information

Note

If you are using a Windows terminal emulator as a console, it is
recommended that you use the Windows Hyper Terminal application.

Step 2

Power on the WLSE.

When the system finishes booting, a login prompt appears on the console.

Step 3

At the login prompt, enter

setup

When you boot the system for the first time, it is not configured. Logging in as

setup

allows you to configure the system.

Step 4

Enter responses to the first set of prompts to configure the WLSE’s network
parameters.

Table 3-2

describes how to respond to the prompts. After each

response, press

Enter

to proceed to the next prompt.

Table 3-2

General Configuration

Prompt

Response Description

Sample Response

host name:

System host name.

SolutionEngine

domain name:

System domain name.

cisco.com

<admin> password:

Sets the password for the default user

admin

. Characters

you type do not appear on screen.

Note

Default user

admin

is reserved and cannot be

deleted or changed.

You can use the admin password to log into the Web
interface and and to connect via Telnet/SSH.

The admin user has system administrator privileges and
can use all CLI commands and all functions in the Web
interface.

Password length is unlimited, and you can use any
characters except the double quote ("), single quote (’),
and dollar sign ($). Passwords are case sensitive.

wq1Cvu2pl

confirm password:

eth0 IP address:

IP address of Ethernet 0 interface.

209.165.200.224

eth0 network mask:

Network mask of Ethernet 0 interface.

255.255.255.224

default gateway IP

address:

IP address of default router.

209.165.200.224

Содержание CiscoWorks WLSE 1130-19









































































































Результаты поиска

Содержание CiscoWorks WLSE 1130-19

Отзывы:

Похожие инструкции для CiscoWorks WLSE 1130-19

Бренды по названию

Популярные бренды

Cisco CiscoWorks WLSE 1130-19, Руководство по установке и настройке

Результаты поиска

Содержание CiscoWorks WLSE 1130-19

Отзывы:

Похожие инструкции для CiscoWorks WLSE 1130-19

Бренды по названию

Популярные бренды