Cisco CiscoWorks WLSE 1130-19 Скачать руководство пользователя страница 13

Страница: 13 / 104

xiii

Installation and Configuration Guide for the CiscoWorks Wireless LAN Solution Engine

78-16778-01

Preface

This document describes the Wireless LAN Solution Engine (WLSE) and
provides instructions for installing and configuring it.

The information in this document applies to the CiscoWorks 1130-19 WLSE and
the CiscoWorks 1130 WLSE as follows:

•

The hardware installation information and technical specifications apply

only

to the CiscoWorks 1130-19 Wireless LAN Solution Engine.

•

The software information applies to WLSE 2.9 software running on

both

the

CiscoWorks 1130-19 WLSE and the CiscoWorks 1130 WLSE.

This guide contains the following sections:

•

Cisco 90-Day Limited Hardware Warranty Terms

•

Supplemental License Agreement

•

Product Overview

•

Installing WLSE 1130-19 Hardware

•

Setting Up the WLSE

•

Setting Up Devices—Overview

•

Setting Up Discovery and Device Management

•

Technical Specifications for the WLSE 1130-19

Содержание CiscoWorks WLSE 1130-19









































































































Результаты поиска

Содержание CiscoWorks WLSE 1130-19

Отзывы:

Похожие инструкции для CiscoWorks WLSE 1130-19

Бренды по названию

Популярные бренды

Cisco CiscoWorks WLSE 1130-19, Руководство по установке и настройке

Результаты поиска

Содержание CiscoWorks WLSE 1130-19

Отзывы:

Похожие инструкции для CiscoWorks WLSE 1130-19

Бренды по названию

Популярные бренды