Circutor Computer SMART III 12 Скачать руководство пользователя страница 89

Страница: 89 / 114

5�15�- DISPLAY

In this point the lighting status of the screen and its language can be configured.
Press the

key to enter edit mode. It is identified by the

symbol and the flashing of the

digits to be modified.

The following display configuration options are available:



: the display light is always on.



OFF

: the light is always off.



AUTO

: the light comes on when a key is pressed and switches off when no keys have been

pressed for 5 minutes.

The light level is also configured between 0 % and 100 % when the display is on.

The display language options are as follows:



ESP

: Spanish,

EnG

: English,

FrA

: French,

: Turkish.

The

key increases the digit value or shows the next option.

The

key reduces the digit value or shows the next option.

The

key skips to the next parameter.

The

key skips to the next parameter.

Press

to validate the data; the

symbol disappears from the display.

Press the

key to access the next programming step.

If no keys are pressed for 5 minutes, the device switches to the simulation screen,

“5.30.- SIMULATION

SCREEN”

Instruction Manual

Computer SMART III

Содержание Computer SMART III 12



















































































































Результаты поиска

Содержание Computer SMART III 12

Отзывы:

Похожие инструкции для Computer SMART III 12

Бренды по названию

Популярные бренды

Circutor Computer SMART III 12, Инструкция по эксплуатации

Результаты поиска

Содержание Computer SMART III 12

Отзывы:

Похожие инструкции для Computer SMART III 12

Бренды по названию

Популярные бренды