Circutor Computer SMART III 12 Скачать руководство пользователя страница 78

Страница: 78 / 114

5�5�- CONNECTION TYPE

In this point the connection type of the installation is selected, where:

3u3C

3 vo neutral and 3 currents.

3u1C

3 vo neutral and 1 current.

2u1C

2 voltages and 1 current.

Press the

key to enter edit mode. It is identified by the

symbol and the flashing of the

digits to be modified.
The

key shows the next option and the

key shows the previous option.

Press

to validate the data; the

symbol disappears from the display.

Press the

key to access the next programming step.

If no keys are pressed for 5 minutes, the device switches to the simulation screen,

“5.30.- SIMULATION

SCREEN”

5�6�- PHASE CONNECTION

This parameter is used to adapt the device to the various options for connecting the power supply and

measurement cables and the current transformers to the phases of the three-phase system.

The connection screen changes according to the connection type programmed in the preceding point.



Connection type

3u1C

2u1C

If a connection with a single current has been selected

(

3u1C

2u1C

)

, one of the 6 possible

phases indicated in

Table 42

are selected in this screen.

The selection of one or another of the options must be made when inductive reactive power with an

inductive cos

of 0.6 to 1 is being consumed in the installation at the time of adjustment. The various

options are tried until the screen shows a cos

of 0.6 to 1 (the display of the cos

is only informative,

not editable).

Computer SMART III

Instruction Manual

Содержание Computer SMART III 12



















































































































Результаты поиска

Содержание Computer SMART III 12

Отзывы:

Похожие инструкции для Computer SMART III 12

Бренды по названию

Популярные бренды

Circutor Computer SMART III 12, Инструкция по эксплуатации

Результаты поиска

Содержание Computer SMART III 12

Отзывы:

Похожие инструкции для Computer SMART III 12

Бренды по названию

Популярные бренды