Circutor Computer SMART III 12 Скачать руководство пользователя страница 90

Страница: 90 / 114

5�16�- ANALOGUE BAR

In this point the parameter to be displayed in the analogue bar (

“4.4.3. ANALOGUE BAR”

) can be

configured.
Press the

key to enter edit mode. It is identified by the

symbol and the flashing of the

digits to be modified.

The following display options are available for the analogue bar:



POTC

: the percentage of power connected to the capacitor bank relative to the total power.



THdI

: the Current THD of each phase.



: the current % of each one of the phases.



: no parameters are displayed.

The

key shows the next option.

The

key shows the previous option.

Press

to validate the data; the

symbol disappears from the display.

Press the

key to access the next programming step.

If no keys are pressed for 5 minutes, the device switches to the simulation screen,

“5.30.- SIMULATION

SCREEN

”

5�17�- FAN

In this point the activation of the relay output associated with the fan can be configured.
It is possible to configure whether or it is enabled

or not

OFF

, as well as the temperature above

which it is to be activated or deactivated.

The device has a hysteresis value of 5ºC when disconnecting the fan, in order to avoid continuous

connections and disconnections.

Computer SMART III

Instruction Manual

Содержание Computer SMART III 12



















































































































Результаты поиска

Содержание Computer SMART III 12

Отзывы:

Похожие инструкции для Computer SMART III 12

Бренды по названию

Популярные бренды

Circutor Computer SMART III 12, Инструкция по эксплуатации

Результаты поиска

Содержание Computer SMART III 12

Отзывы:

Похожие инструкции для Computer SMART III 12

Бренды по названию

Популярные бренды