Circutor Computer SMART III 12 Скачать руководство пользователя страница 71

Страница: 71 / 114

5.- CONFIGURATION

The various configuration parameters of the device can be consulted and edited in the device setup

menu.

The device always keeps the capacitors disconnected (except in the Plug&Play function).

This status is identified by the

symbol in the device status area of the display (

Figure 15

To access the setup menu, long keystroke the

key (> 3 s).

The Password screen appears on the display. The password to be entered is a combination of keys:

. It is unique and cannot be configured.

If it is not entered correctly, the device returns to the previous measurement screen.

If it is entered correctly and capacitors are connected, the disconnection screen appears.

Disconnection screen: used for the device to automatically disconnect all the stages before entering

the configuration.

While in this screen, the device does not respond to the keypad.

The device automatically exits this screen, and this can take a certain amount of time.

Instruction Manual

Computer SMART III

Содержание Computer SMART III 12



















































































































Результаты поиска

Содержание Computer SMART III 12

Отзывы:

Похожие инструкции для Computer SMART III 12

Бренды по названию

Популярные бренды

Circutor Computer SMART III 12, Инструкция по эксплуатации

Результаты поиска

Содержание Computer SMART III 12

Отзывы:

Похожие инструкции для Computer SMART III 12

Бренды по названию

Популярные бренды