Circutor Computer SMART III 12 Скачать руководство пользователя страница 44

Страница: 44 / 114

Table 10 (Continuation): Alarm codes�

Code

Description

E12

Disconnection Status

due to

E08

E09

E10

E13

Leakage Alarm

. The leakage current is higher than that configured in the

Leakage Current alarm.

E14

Repeated Leakage Alarm

. Leakages have been detected repeatedly in the system,but they

are not caused by a capacitor.

E15

Leakage in Capacitors Alarm

. Leakages have been detected, which were caused by some of

the capacitors, and this stage is disabled. The disabled capacitors will start to flash on the
screen. In addition, the

E13

message will be displayed.

In order to enable these capacitors again, view the configuration of the Leakage alarm.

E16

Leakage transformer detection Alarm�

The Leakage alarm has been enabled, but the device

does not detect the connection of the leakage current transformer.

E17

Number of connections alarm�

The configured number of operations has been exceeded (any

capacitor)

In these alarms, two levels have been configured:



The

value:

When the device exceeds this value during 30 minutes, the corresponding

alarm is triggered and, if alarm

E11

is enabled, the

Computer SMART III

device enters the

Connection

status and activates

alarm

E11



The

value:

if the device exceeds this value during 30 seconds, the corresponding alarm is

triggered and, if alarm

E12

is enabled, the

Computer SMART III

device enters the

Disconnection

status and activates alarm

E12

If the device falls back under the Lo value during 10 minutes, it deactivates the alarms and returns to

the normal operating status.

In the

No Connection

status, the device does not connect the stages, but also does not disconnect

them if the operation requires it.

In the

Disconnection

status, it disconnects the stages and does not allow them to connect.

Computer SMART III

Instruction Manual

Содержание Computer SMART III 12



















































































































Результаты поиска

Содержание Computer SMART III 12

Отзывы:

Похожие инструкции для Computer SMART III 12

Бренды по названию

Популярные бренды

Circutor Computer SMART III 12, Инструкция по эксплуатации

Результаты поиска

Содержание Computer SMART III 12

Отзывы:

Похожие инструкции для Computer SMART III 12

Бренды по названию

Популярные бренды