Chrysler 300 SRT8 2010 Скачать руководство пользователя страница 341 | Manualshive

Страница: 341 / 449

background image

(D) Securing TIREFIT Sealant in the Tire:

Immediately after injecting sealant, and inflating tire,
drive the vehicle 5 miles (8 km) or 10 minutes to ensure
distribution of the TIREFIT Sealant within the tire. Do not
exceed 55 mph (88 km/h).

WARNING!

TIREFIT is not a permanent flat tire repair. Have the
tire inspected and repaired or replaced after using
TIREFIT. Do not exceed 55 mph (88 km/h) until
having the tire repaired or replaced. Failure to follow
this warning can result in injuries that are serious or
fatal to you, your passengers, and others around you.

(E) After Securing TIREFIT Sealant in the Tire:

Follow Step (A) “Whenever You Stop to Use TIREFIT”
before continuing.

1. Turn the Mode Select knob (4) to the Air Mode
position.

2. Uncoil the Black Air Pump Hose (6) and connect it to
the valve stem.

3. Check the pressure in the tire by reading the Pressure
Gauge (2).

If tire pressure is less than 19 psi (1.3 Bar)

, the tire is too

badly damaged. Do not attempt to drive the vehicle
further. Call for assistance.

If the tire pressure is 19 psi (1.3 bar) or higher:

1. Press the power button (3) to on and inflate the tire to
the pressure indicated on the tire and loading informa-
tion label on the driver-side door opening.

2. Disconnect the TIREFIT kit from the valve stem and
then reinstall the cap on the valve stem.

6

WHAT TO DO IN EMERGENCIES

341

«
...
339
340
341
342
343
...
»

Содержание 300 SRT8 2010


































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 300 SRT8 2010

Бренд: Wallbox Страницы: 7

Бренд: TBC Страницы: 12

Бренд: Ford Страницы: 2

Intercooler Kit Type 31

Бренд: GReddy Страницы: 9

Бренд: A-Tach Страницы: 2

Бренд: ULTIMATE SPEED Страницы: 50

Бренд: Camecho Страницы: 2

E60-82-007-02-10

Бренд: Eibach Страницы: 3

GMC Yukon Denali 2005

Бренд: Cadillac Страницы: 456

Бренд: Saab Страницы: 63

Бренд: R&G Страницы: 20

Бренд: Whispbar Страницы: 70

Бренд: Horn Tools Страницы: 12

2007 SLR Mclaren

Бренд: Mercedes-Benz Страницы: 425

Бренд: Mopar Страницы: 17

Бренд: Car-Interface Страницы: 23

Бренд: Buick Страницы: 58

Бренд: Scosche Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды