Chrysler 300 SRT8 2010 Скачать руководство пользователя страница 332 | Manualshive

Страница: 332 / 449

background image

HAZARD WARNING FLASHER

The Hazard Warning flasher switch is located in the center
of the instrument panel between the center air outlets.

Press the switch to turn on the Hazard Warning
flasher. When the switch is activated, all directional
turn signals will flash on and off to warn oncoming

traffic of an emergency. Press the switch a second time to
turn off the Hazard Warning flasher.

This is an emergency warning system and it should not
be used when the vehicle is in motion. Use it when your
vehicle is disabled and it is creating a safety hazard for
other motorists.

When you must leave the vehicle to seek assistance, the
Hazard Warning flasher will continue to operate even
though the ignition is placed in the OFF position.

NOTE:

With extended use the Hazard Warning flasher

may wear down your battery.

IF YOUR ENGINE OVERHEATS

In any of the following situations, you can reduce the
potential for overheating by taking the appropriate action.

•

On the highways — slow down.

•

In city traffic — while stopped, place the transmission
in NEUTRAL, but do not increase the engine idle
speed.

CAUTION!

Driving with a hot cooling system could damage
your vehicle. If the temperature gauge reads 240°F
(116°C) or greater pull over and stop the vehicle. Idle
the vehicle with the air conditioner turned off until
the pointer drops back into the normal range 200–
230°F (93–110°C). If the pointer remains at 240°F
(116°C) or greater and you hear a chime, turn the
engine off immediately and call for service.

332

WHAT TO DO IN EMERGENCIES

«
...
330
331
332
333
334
...
»

Содержание 300 SRT8 2010


































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 300 SRT8 2010

Бренд: Daihatsu Страницы: 1718

Бренд: PEUGEOT Страницы: 128

Бренд: Schumacher Electric Страницы: 87

2009 ESCALADE ESV

Бренд: Cadillac Страницы: 602

Бренд: CITROEN Страницы: 52

Бренд: Prorack Страницы: 14

Бренд: Quadratec Страницы: 12

Бренд: A-Tach Страницы: 2

Бренд: Mercedes-Benz Страницы: 358

Бренд: Ford Страницы: 256

Бренд: Velleman Страницы: 12

Vehicle Asset Communicator

Бренд: I.D. Systems Страницы: 41

Бренд: Subaru Страницы: 19

Бренд: S3 Power Sports Страницы: 2

2004 Impreza OUTBACK SPORT

Бренд: Subaru Страницы: 34

Бренд: Toyota Страницы: 497

Бренд: RAM Страницы: 148

Бренд: Hamron Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды