Chrysler 300 SRT8 2010 Скачать руководство пользователя страница 318 | Manualshive

Страница: 318 / 449

background image

If the ignition key is cycled, this sequence will repeat,
providing the system fault still exists. If the system fault
no longer exists, the TPM Telltale Light will no longer
flash, and the

⬙

CHECK TPM SYSTEM

⬙

message will no

longer display, and a pressure value will display in place
of the dashes. A system fault can occur due to any of the
following:

1. Signal interference due to electronic devices or driving
next to facilities emitting the same radio frequencies as
the TPM sensors.

2. Installing aftermarket window tinting that contains
materials that may block radio wave signals.

3. Accumulation of snow or ice around the wheels or
wheel housings.

4. Using tire chains on the vehicle.

5. Using wheels/tires not equipped with TPM sensors.

Vehicles with Full Size Spare

1. The matching full size spare wheel and tire assembly
has a TPM sensor that can be monitored by the TPMS.

2. If you install the full size spare in place of a road tire
that has a pressure below the low-pressure warning limit,
upon the next ignition key cycle, a chime will sound and
the TPM Telltale Light will turn ON. In addition, the
EVIC will display a low pressure message and a graphic
showing the low tire pressure value flashing.

3. After driving the vehicle for up to 20 minutes above
15 mph (25 km/h) the TPM Telltale Light will turn OFF,
as long as no tire pressure is below the low-pressure
warning limit in any of the four active road tires.

Vehicles with Compact Spare

1. The compact spare tire does not have a TPM sensor.
Therefore, the TPMS will not monitor the pressure in the
compact spare tire.

318

STARTING AND OPERATING

«
...
316
317
318
319
320
...
»

Содержание 300 SRT8 2010


































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 300 SRT8 2010

Car Top Duffle Bag

Бренд: Rightline Gear Страницы: 2

Бренд: Haibang Страницы: 6

Бренд: Axxess Страницы: 8

Бренд: Yescom Страницы: 4

Бренд: Z Automotive Страницы: 16

Бренд: Ford Страницы: 8

Бренд: Intec Страницы: 16

Бренд: Vauxhall Страницы: 131

Бренд: Hummer Страницы: 31

2007 SLR Mclaren

Бренд: Mercedes-Benz Страницы: 425

Бренд: Chevrolet Страницы: 55

1997 Park Avenue

Бренд: Buick Страницы: 420

Бренд: Whelen Engineering Company Страницы: 2

Бренд: Lexus Страницы: 94

Бренд: Chrysler Страницы: 17

2013 Pilot Touring

Бренд: Honda Страницы: 18

Бренд: Hendrickson Страницы: 60

Off Camber Fabrications 130717

Бренд: MBRP Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды