Chrysler 300 SRT8 2010 Скачать руководство пользователя страница 344 | Manualshive

Страница: 344 / 449

background image

WARNING! (Continued)

•

Do not use a booster battery or any other booster
source that has a greater than 12 Volt system, i.e.,
do not use a 24 Volt power source.

•

The battery in this vehicle has a vent hose that
should not be disconnected and should only be
replaced with a battery of the same type (vented).

NOTE:

The battery is stored under an access cover in

the trunk. Remote battery terminals are located in the
engine compartment for jump-starting.

1. Wear eye protection and remove any metal jewelry
such as watchbands or bracelets that might make an
inadvertent electrical contact.

2. When boost is provided by a battery in another
vehicle, park that vehicle within booster cable reach, but
do not allow the vehicles to touch one another.

WARNING!

Do not permit vehicles to touch each other as this
could establish a ground connection and personal
injury could result.

3. Set the parking brake, place the automatic transmis-
sion in PARK, and place the ignition to the OFF/ LOCK
position on both vehicles.

4. Turn off the heater, radio, and all unnecessary electri-
cal loads.

5. Connect one end of the jumper cable to the remote
jump-start positive battery post

(+)

in the engine com-

partment. Connect the other end of the same cable to the
positive terminal of the booster battery. Refer to the
following illustration for jump-starting connections.

6. Connect the other cable, first to the negative terminal
of the booster battery and

then to the ground (-) of the

344

WHAT TO DO IN EMERGENCIES

«
...
342
343
344
345
346
...
»

Содержание 300 SRT8 2010


































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 300 SRT8 2010

Бренд: Mazda Страницы: 4

Бренд: Davis Instruments Страницы: 16

Бренд: Horn Tools Страницы: 6

STRONGARM RVR303

Бренд: Blue Giant Страницы: 48

Бренд: WABCO Страницы: 32

51 47 0 027 792

Бренд: BMW Страницы: 7

Бренд: Ford Страницы: 728

Бренд: Westin Страницы: 5

Бренд: THIEYE Страницы: 88

Бренд: Honda Страницы: 124

Бренд: NavLinkz Страницы: 23

Бренд: Whispbar Страницы: 15

Бренд: Honda Страницы: 330

Бренд: RADICAL Страницы: 11

Бренд: Yakima Страницы: 10

Бренд: Yakima Страницы: 12

Бренд: Stanley Страницы: 6

Бренд: Macally Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды