Chrysler 300 SRT8 2010 Скачать руководство пользователя страница 333 | Manualshive

Страница: 333 / 449

background image

NOTE:

There are steps that you can take to slow down

an impending overheat condition:

•

If your air conditioner (A/C) is on, turn it off. The A/C
system adds heat to the engine cooling system and
turning the A/C off can help remove this heat.

•

You can also turn the temperature control to maximum
heat, the mode control to floor and the blower control
to high. This allows the heater core to act as a
supplement to the radiator and aids in removing heat
from the engine cooling system.

WARNING!

A hot engine cooling system is dangerous. You or
others could be badly burned by steam or boiling
coolant. You may want to call a service center if your
vehicle overheats. If you decide to look under the
hood yourself, refer to Section 7 and follow the
warnings under the “Cooling System Pressure Cap”
paragraph.

TIREFIT KIT

Small punctures up to

1

⁄

4

” (6 mm) in the tire tread can be

sealed with TIREFIT. Foreign objects (e.g., screws or
nails) should not be removed from the tire. TIREFIT can
be used in outside temperatures down to approximately
-4°F (-20°C).

This kit will provide a temporary tire seal, allowing you
to drive your vehicle up to 100 miles (160 km) with a
maximum speed of 55 mph (88 km/hr).

6

WHAT TO DO IN EMERGENCIES

333

«
...
331
332
333
334
335
...
»

Содержание 300 SRT8 2010


































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 300 SRT8 2010

Бренд: Metra Electronics Страницы: 14

Electronic Parking Disc 3

Бренд: Jacob Jensen Страницы: 2

Бренд: Yakima Страницы: 12

Бренд: Mazda Страницы: 720

Бренд: Phonocar Страницы: 6

Бренд: WABCO Страницы: 32

Бренд: Webasto Страницы: 34

Бренд: Ecco Страницы: 12

Бренд: METRON Страницы: 4

PRIME DESIGN URX-001-E

Бренд: Safe Fleet Страницы: 8

Бренд: Pyle Страницы: 2

Бренд: ROADGEAR Страницы: 2

Бренд: Volvo Страницы: 362

Бренд: walser Страницы: 8

Бренд: Honda Страницы: 76

Бренд: Volkswagen Zubehör Страницы: 40

Бренд: Intellitronix Страницы: 11

Бренд: GMC Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды