Chrysler 300 SRT8 2010 Скачать руководство пользователя страница 292 | Manualshive

Страница: 292 / 449

background image

stopped with the engine running. After five seconds, a
chime will sound, the “ESP/TCS Indicator Light” will
illuminate, and the

⬙

ESP OFF

⬙

message will display in the

vehicle odometer. Press and release the TRIP ODOM-
ETER button located on the instrument cluster to clear
this message. The “ESP OFF” message may appear in the
Electronic Vehicle Information Center (EVIC). Refer to
“Electronic Vehicle Information Center (EVIC)” in Sec-
tion 4. To turn ESP ON again, momentarily press the
“ESP OFF” switch.

NOTE:

The

⬙

ESP OFF

⬙

message will display and the

audible chime will sound when the shift lever is moved
into the PARK position from any position other than
PARK and then moved out of the PARK position. This
will occur when the message was previously cleared.

WARNING!

In the ESP “Full Off” mode, the engine torque
reduction and stability features are cancelled. There-
fore, the enhanced vehicle stability offered by ESP is
unavailable.

NOTE:

When the ESP is switched OFF, a feature of the

system remains active. This feature controls wheel spin
across an axle quite similarly to a limited slip differential.
If one wheel on an axle is spinning faster than the other,
the system will apply the brake of the spinning wheel
and allow more engine torque to be applied to the wheel
that is not spinning. To improve the vehicle’s traction
when driving with tire chains, or when starting off in
deep snow, sand, or gravel, it may be desirable to switch
to the “Partial Off” mode by momentarily pressing the
“ESP OFF” switch.

292

STARTING AND OPERATING

«
...
290
291
292
293
294
...
»

Содержание 300 SRT8 2010


































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 300 SRT8 2010

Бренд: U.S. General Страницы: 5

Бренд: Acdeos Страницы: 7

Бренд: Cadillac Страницы: 3

Бренд: Cadillac Страницы: 12

Бренд: Cadillac Страницы: 106

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 326

Бренд: Cadillac Страницы: 28

ESCALADE - BROCHURE 2009

Бренд: Cadillac Страницы: 602

ESCALADE ESV 2004

Бренд: Cadillac Страницы: 20

ESCALADE EXT 2005

Бренд: Cadillac Страницы: 460

CT6 SUPER CRUISE 2018

Бренд: Cadillac Страницы: 8

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 337

Бренд: HALE Страницы: 44

Бренд: LAS Страницы: 44

Бренд: LAS Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды