Chrysler 300 SRT8 2010 Скачать руководство пользователя страница 313 | Manualshive

Страница: 313 / 449

background image

TIRE PRESSURE MONITOR SYSTEM (TPMS)

The Tire Pressure Monitor System (TPMS) will warn the
driver of a low tire pressure based on the vehicle recom-
mended cold placard pressure.

The tire pressure will vary with temperature by about
1 psi (6.9 kPa) for every 12°F (6.5°C). This means that
when the outside temperature decreases, the tire pressure
will decrease. Tire pressure should always be set based
on cold inflation tire pressure. This is defined as the tire
pressure after the vehicle has not been driven for at least
three hours, or driven less than 1 mile (1 km) after a three
hour period. The cold tire inflation pressure must not
exceed the maximum inflation pressure molded into the
tire sidewall. Refer to the “Tires – General Information”
in this section for information on how to properly inflate
the vehicle’s tires. The tire pressure will also increase as
the vehicle is driven - this is normal and there should be
no adjustment for this increased pressure.

The TPMS will warn the driver of a low tire pressure if
the tire pressure falls below the low-pressure warning
limit for any reason, including low temperature effects
and natural pressure loss through the tire.

The TPMS will continue to warn the driver of low tire
pressure as long as the condition exists, and will not turn
off until the tire pressure is at or above the recommended
cold placard pressure. Once the low tire pressure warn-
ing (Tire Pressure Monitoring [TPM] Telltale Light) illu-
minates, you must increase the tire pressure to the
recommended cold placard pressure in order for the TPM
Telltale Light to turn off. The system will automatically
update and the TPM Telltale Light will turn off once the
system receives the updated tire pressures. The vehicle
may need to be driven for up to 20 minutes above 15 mph
(25 km/h) in order for the TPMS to receive this informa-
tion.

5

STARTING AND OPERATING

313

«
...
311
312
313
314
315
...
»

Содержание 300 SRT8 2010


































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 300 SRT8 2010

Бренд: ULTIMATE SPEED Страницы: 19

V2 SUPERCHARGER

Бренд: Tesla Страницы: 9

3-series convertible

Бренд: BMW Страницы: 98

Бренд: V8 equipment Страницы: 17

1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28

Бренд: Havis-Shields Страницы: 3

FIX&GO automatic

Бренд: Alfa Romeo Страницы: 40

Бренд: GMC Страницы: 20

Бренд: BrandMotion Страницы: 2

Бренд: Hummer Страницы: 502

Impala Limited 2014

Бренд: Chevrolet Страницы: 356

Бренд: STARLANE Страницы: 24

Бренд: RAM Страницы: 13

Бренд: FALCON RIDGE Страницы: 4

Бренд: iDataLink Страницы: 6

FlashLogic FLC-FORS-FO1B-FLRSFO1-EN

Бренд: ADS Страницы: 25

Бренд: Westfalia Страницы: 10

1995 C/K Pickup

Бренд: Chevrolet Страницы: 483

Бренд: HOLDEN Страницы: 330

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды