Chrysler 300 SRT8 2010 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 449

background image

BeltAlert

威

will be reactivated if the driver’s seat belt is

unbuckled for more than 10 seconds and the vehicle
speed is greater than 5 mph (8 km/h).

BeltAlert

威

Programming

The BeltAlert

威

can be enabled or disabled by your

authorized dealer or by performing the following steps:

NOTE:

Chrysler Group LLC does not recommend de-

activating the BeltAlert

威

.

1. With all doors closed, and the ignition switch in any
position except RUN or START, buckle the driver’s seat
belt.

2. Turn the ignition switch to the RUN position, but do
not start the engine. Wait for the Seat Belt Reminder Light
to turn off and then proceed to the next step.

NOTE:

You must perform the following steps within

60 seconds of turning the ignition switch to the RUN
position.

3. Within 60 seconds of turning the ignition switch to the
RUN position, unbuckle and then re-buckle the driver’s
seat belt at least three times within 10 seconds, ending
with the seat belt buckled.

NOTE:

Watch for the Seat Belt Reminder Light to turn

on while unbuckling the seat belt and turn off while
re-buckling the seat belt. It may be necessary to retract
the seat belt.

4. Turn the ignition switch to the OFF position. A single
chime will sound to signify that you have successfully
completed the programming.

BeltAlert

威

can be reactivated by repeating this procedure.

52

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
50
51
52
53
54
...
»

Содержание 300 SRT8 2010


































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 300 SRT8 2010

Бренд: Happy Orange Страницы: 2

Бренд: Jeep Страницы: 322

Бренд: Jeep Страницы: 341

Бренд: Jeep Страницы: 310

Бренд: Jeep Страницы: 189

Бренд: Jeep Страницы: 26

Бренд: Jeep Страницы: 21

Бренд: Porsche Страницы: 144

Бренд: Cargo Floor Страницы: 16

1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28

Бренд: Havis-Shields Страницы: 3

Бренд: Cadillac Страницы: 518

Бренд: Opel Страницы: 141

Бренд: AEM Страницы: 27

Бренд: GMC Страницы: 430

Бренд: MULTILIFT Страницы: 62

Бренд: ULTIMATE SPEED Страницы: 32

Бренд: Chevrolet Страницы: 441

Бренд: Needit Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды