Chrysler 300 SRT8 2010 Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 449

background image

NOTE:

•

The Rain Sensing feature will not operate when the
wiper speed is in the low or high position.

•

The Rain Sensing feature may not function properly
when ice or dried salt water is present on the wind-
shield.

•

Use of Rain-X

威

or products containing wax or silicone

may reduce rain sensor performance.

•

The Rain Sensing feature can be enabled or disabled.
Refer to “Rain Sensing Intermittent Wipers,” under
“Personal Settings (Customer-Programmable Features)”
under “Electronic Vehicle Information Center (EVIC)” in
Section 4.

The Rain Sensing system has protective features for the
wiper blades and arms. It will not operate under the
following conditions:

•

Low Temperature Wipe Inhibit

— The Rain Sensing

feature will not operate when the ignition is placed in
the RUN position, the vehicle is stationary and the
outside temperature is below 32°F (0°C), unless the
wiper control on the multifunction lever is moved, the
vehicle speed becomes greater than 0 mph (0 km/h) or
the outside temperature rises above freezing.

•

Neutral Wipe Inhibit

— The Rain Sensing feature will

not operate when the ignition is placed in the RUN
position, the transmission shift lever is in the NEU-
TRAL position and the vehicle speed is less than
5 mph (8 km/h), unless the wiper control on the
multifunction lever is moved or the shift lever is
moved out of the NEUTRAL position.

146

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
144
145
146
147
148
...
»

Содержание 300 SRT8 2010


































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 300 SRT8 2010

Бренд: cam Страницы: 2

Бренд: Dapper Lighting Страницы: 2

Yamaha Rhino 660

Бренд: Yamaha Страницы: 3

Бренд: Yakima Страницы: 8

Sterling ALL-TERRAIN 576

Бренд: Roadmaster Страницы: 12

Бренд: Fiat Страницы: 172

Бренд: Honda Страницы: 6

Бренд: Acura Страницы: 2

Бренд: BMW Страницы: 21

Бренд: Inbay Страницы: 20

Бренд: Quadratec Страницы: 12

Бренд: Ecco Страницы: 12

Бренд: Sanitas Страницы: 36

Бренд: RAM Страницы: 13

Бренд: cam Страницы: 28

Бренд: Rugged Ridge Страницы: 5

Бренд: V8 equipment Страницы: 34

Бренд: Prime Design Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды