Chrysler 300 SRT8 2010 Скачать руководство пользователя страница 336 | Manualshive

Страница: 336 / 449

background image

the vehicle or tire and wheel components. Once the
sealant dries, it can easily be peeled off and properly
discarded.

•

For optimum performance, make sure the valve stem
on the wheel is free of debris before connecting the
TIREFIT kit.

•

You can use the TIREFIT air pump to inflate bicycle
tires. The kit also comes with two needles located in
the Accessory Storage Compartment (8) for inflating
sport balls, rafts, or like inflatable items. However, use
only the Black Air Pump Hose (6) and make sure the
Mode Select Knob (4) is in the Air Mode when
inflating such items to avoid injecting sealant into
them. The TIREFIT Sealant is only intended to seal
punctures less than

1

⁄

4

” (6mm) diameter in the tread of

your vehicle.

•

Do not lift or carry TIREFIT kit by hoses.

WARNING!

•

Do not attempt to seal a tire on the side of the
vehicle close to traffic. Pull far enough off the road
to avoid the danger of being hit when using the
TIREFIT kit.

•

Do not use TIREFIT or drive the vehicle under the
following circumstances:
− If the cut or puncture in the tire tread is approxi-
mately 0.24 in. (6 mm) or larger.
− If the tire has any sidewall damage.
− If the tire has any damage from driving with
extremely low tire pressure.
− If the tire has any damage from driving on a flat
tire.
− If the wheel has any damage.

(Continued)

336

WHAT TO DO IN EMERGENCIES

«
...
334
335
336
337
338
...
»

Содержание 300 SRT8 2010


































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 300 SRT8 2010

Бренд: Acdeos Страницы: 38

Бренд: CAMPARK Страницы: 20

Бренд: DANA Страницы: 42

Бренд: dallara Страницы: 37

Бренд: Yakima Страницы: 8

RadioPRO 5 RP5-GM41

Бренд: PAC Страницы: 3

21 COVERT Series

Бренд: Code 3 Страницы: 16

Бренд: TATA Motors Страницы: 156

Lippert Components LEVELEGS MPD 66385

Бренд: Atwood Страницы: 6

65 41 2 152 528

Бренд: BMW Страницы: 21

10-8002-C11670C

Бренд: Saleen Страницы: 17

PACCAR PACMOBILE 20

Бренд: DAF Страницы: 18

Xplore Pro II SxS

Бренд: Marlon Страницы: 15

Бренд: PAC Страницы: 14

Бренд: Kolpin Страницы: 3

LED Dominator TAM83S2

Бренд: Whelen Engineering Company Страницы: 2

Jumpy Miltispace

Бренд: CITROËN Страницы: 164

Бренд: Directed Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды