Chrysler 300 SRT8 2010 Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 449

background image

If either light remains on and does not flash, or there is a
very fast flash rate, check for a defective outside light
bulb. If an indicator fails to light when the lever is
moved, it would suggest that the indicator bulb is
defective.

NOTE:

A “Turn Signal On” message will appear in the

EVIC and a continuous chime will sound if the vehicle is
driven more than 1 mile (1.6 km) with either turn signal
on.

Lane Change Assist

Tap the lever up or down once, without moving beyond
the detent, and the turn signal (right or left) will flash
three times then automatically turn off.

High/Low Beam Switch

Push the multifunction lever away from you to switch
the headlights to high beam. Pull the multifunction lever
toward you to switch the headlights back to low beam.

Flash-To-Pass

You can signal another vehicle with your headlights by
lightly pulling the multifunction lever toward you. This
will cause the headlights to turn on at high beam and
remain on until the multifunction lever is released.

Overhead Console Map/Reading Lights

These lights are mounted between the sun visors on the
overhead console. Each light is turned on by pressing the
lens. Press the lens a second time to turn off the light.
These lights also turn on when a door is opened, or when

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

141

«
...
139
140
141
142
143
...
»

Содержание 300 SRT8 2010


































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 300 SRT8 2010

Бренд: Yakima Страницы: 11

Бренд: RAM Страницы: 116

Бренд: Mitsubishi Страницы: 160

Бренд: Cadillac Страницы: 442

2011 Civic Sedan

Бренд: Honda Страницы: 5

990E0-54P56-000

Бренд: Suzuki Страницы: 12

Бренд: Toyota Страницы: 636

Бренд: Cadillac Страницы: 402

Бренд: Cobra Страницы: 2

Бренд: Caltrend Страницы: 3

Бренд: Volvo Страницы: 123

Бренд: Aries Страницы: 3

Бренд: RAM Страницы: 5

CHALLENGER GK-6125A 2018

Бренд: Coolster Страницы: 45

Filtercharger 57-9004

Бренд: K&N Engineering Страницы: 4

Бренд: Honda Страницы: 219

Бренд: Menabo Страницы: 12

Бренд: Edelbrock Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды