Checkline TI-007DLX Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 46

background image

– 10 –

The top end cap is where all connections are made to the TI-007DLX. The diagram
above shows the layout and description of the connectors.

Transducer Connectors

Refer to Diagram: The transducer connectors and battery cover/probe zero disk are
located on the TI-007DLX ’s top end cap. The transducer connectors are of type Lemo
“00”.

Probe Zero Disk & Battery Cover

Refer to Diagram: The Battery cover is the large round disk shown in the diagram.

NOTE:

This same disk is also used as a probe zero reference disk. Simply remove the

cover when replacing the batteries (2 AA cells). When performing a manual probe zero
function, simply place the transducer on disk making firm contact. Important: Be sure
the battery polarity is correct, which can be found on the back label of the TI-007DLX.

NOTE:

Rechargeable batteries can be used, however they must be recharged outside of

the unit in a standalone battery charger.

USB-C Connector

Refer to Diagram: The USB-C connector, located on the bottom end cap, is a mini
type C female connector. It is designed to connect directly from the TI-007DLX to
a standard USB type A port on a PC. The cable supplied with the TI-007DLX is a
USB type C to a USB type A (pt# N-003-0330). See section 9.1 for information on
connectivity.

NOTE:

This connector is also used to upgrade the TI-007DLX with the latest version of

firmware.

«
...
9
10
11
12
13
...
»

Содержание TI-007DLX















































Отзывы:

Нет отзывов

Похожие инструкции для TI-007DLX

Бренд: Kane Страницы: 12

Бренд: Bacharach Страницы: 19

Бренд: Landis+Gyr Страницы: 26

Бренд: Landis+Gyr Страницы: 3

CP-4900 Micro-GC

Бренд: Varian Страницы: 13

Бренд: WATERGUARD Страницы: 2

Бренд: ZHYQ Страницы: 6

Бренд: Hanna Instruments Страницы: 2

Бренд: Keeler Страницы: 68

Бренд: Jenoptik Страницы: 54

Бренд: Velleman Страницы: 107

Бренд: Guru Home Systems Страницы: 20

Бренд: Analog Arts Страницы: 8

Heavy Duty 2270-20

Бренд: Milwaukee Страницы: 33

Бренд: IDEAL Страницы: 84

Бренд: JBM Страницы: 4

Бренд: Carman Страницы: 64

Бренд: AccuEnergy Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды