Checkline TI-007DLX Скачать руководство пользователя страница 36

Страница: 36 / 46

– 35 –

3. Repeat steps 1 and 2 as needed.

NOTE:

If an area exists where a measurement cannot be obtained successfully,press the

key to store

OBST

(obstruction) in the location. Pressing the

key again will

clear the location.

NOTE:

If a measurement has been previously stored in a location, scrolling to that

location will display the measurement currently stored, and show

MEM

(memory) in

the top right corner of the display. If the

key is pressed to store another

measurement at that location,

FULL

will briefly be displayed on the screen

indicating a measurement has already

been stored at that location.

Pressing the

key will clear the previously stored measurement from the location.

Pressing the

key will now store the new measurement

9.4 Clearing a File

If a file contains a large number of previously stored measurements, and has already
been downloaded, the file will need to be cleared of its measurements.

The following procedure outlines this process:

1. Press the

key to access the data files and display the current file open.

2. Press the

key to edit which file will be cleared. The edit icon will be

illuminated

and flashing.

3. Use the

and

keys to scroll to the file that will be cleared.

4. When

the

desired FILE is being displayed, press the

key to select the file to be cleared.

5. Use the

and

keys to scroll to CLR (clear).

6. Press the

key to display the confirmation screen. CLR? will be displayed,

as well as a flashing Yes/No option.

7. Press the

key for YES, and the

key for NO. The edit icon

will be

illuminated and

flashing.

Содержание TI-007DLX















































Результаты поиска

Содержание TI-007DLX

Отзывы:

Похожие инструкции для TI-007DLX

Бренды по названию

Популярные бренды

Checkline TI-007DLX, Руководство по эксплуатации

Результаты поиска

Содержание TI-007DLX

Отзывы:

Похожие инструкции для TI-007DLX

Бренды по названию

Популярные бренды