Checkline TI-007DLX Скачать руководство пользователя страница 37

Страница: 37 / 46

– 36 –

NOTE:

Pressing the key prior to pressing the key will abort to the measurement screen

without clearing the file.

8. Press the

key to confirm Yes/No selection and return to the measurement

screen.

NOTE:

If Yes was selected a BUSY message will briefly be displayed confirming the

file is being cleared.

9.5 Clear All Files

If a number of files in the TI-007DLX contain old data, or data that has been previously
downloaded, clearing all the files might prove an efficient option.

The following procedure outlines this process:

1. Press the

key to access the data files and display the current file open.

2. Use the

and

keys to scroll to the CLR ALL option.

3. Press the

key to display the confirmation screen. CLR ALL is displayed, as

well as a flashing Yes/No option.

4. Press the

key for YES, and the

key for NO. The edit icon

will

be illuminated and

flashing.

NOTE:

Pressing the

key prior to pressing the

key will abort to the

measurement screen without clearing the files.

5. Press the

key to confirm Yes/No selection and return to the measurement

screen.

NOTE:

If Yes was selected a BUSY message will briefly be displayed confirming the

files are being cleared.

Содержание TI-007DLX















































Результаты поиска

Содержание TI-007DLX

Отзывы:

Похожие инструкции для TI-007DLX

Бренды по названию

Популярные бренды

Checkline TI-007DLX, Руководство по эксплуатации

Результаты поиска

Содержание TI-007DLX

Отзывы:

Похожие инструкции для TI-007DLX

Бренды по названию

Популярные бренды