Chattanooga Group Intelect TRANSPORT Vectra Genisys 2759 Скачать руководство пользователя страница 16

Страница: 16 / 48

Intelect TranSport®/Vectra Genisys® Ultrasound Therapy Systems

5.5 VISUAL INSPECTION

Visually inspect the Intelect Transport/Vectra

Genisys Ultrasound Therapy Systems. A visual

inspection can, to an experienced technician,

indicate possible abuse of the unit and internal

problems.

5.6 UNIT STARTUP AND FAN TESTING

Test

1. Place unit face up on work surface.

2. Connect Power Cord to unit and plug into

proper

power

receptacle.

3. Connect an Applicator to the unit.

4. Turn system on. Adjust the Intensity up and

press Start. The fan will begin to run, after the

audible

beep

tones.

5. Place hand at the back of system, near

Contrast Control, to verify Fan is blowing out.

Refer

Figure

5.1.

B. Test Results

1. Unit will not start, unit failed test.

a) Possible bad Main Power Switch.

b) Possible bad Power Supply.

c) Possible bad power outlet or Mains Power

Cord.

d) Possible bad Ultrasound Board.

2. Treatment will not start up.

a) Applicator not connected.

b) Possible bad Ultrasound Board.

c) Possible bad Control Board.

3. Screen does not display, unit failed test.

a) Contrast Control needs adjusting.

b) Possible bad Display.

c) Possible bad Control Board.

d) Possible bad Power Supply.

e) Visually check power LED. If flashing, the

Power Supply is good. Replace the Control

Board.

f ) If not flashing perform the Ultrasound

Board test to check the Ultrasound Board.

Refer to section 5.7

page 15.

If the Power

Supply functions replace the Ultrasound

Board.

4. Fan not blowing outward, unit failed test

Fan

blowing

inward.

Fan wired wrong. Rewire or replace Fan.

5. Fan not blowing.

NOTE:

The Fan only functions when Ultrasound is

being emitted from the Sound Head.

a) Possible bad Fan.

b) Possible bad Power Supply.

c) Possible bad Control Board.

5 TROUBLESHOOTING

FIGURE 5.1

VERIFY FAN IS

BLOWING OUT

Содержание Intelect TRANSPORT Vectra Genisys 2759

















































Результаты поиска

Содержание Intelect TRANSPORT Vectra Genisys 2759

Отзывы:

Бренды по названию

Популярные бренды

Chattanooga Group Intelect TRANSPORT Vectra Genisys 2759, Руководство по обслуживанию

Результаты поиска

Содержание Intelect TRANSPORT Vectra Genisys 2759

Отзывы:

Бренды по названию

Популярные бренды