CES SDI-50 Скачать руководство пользователя страница 39

Страница: 39 / 48

C.E.S. Model SDI-50 Manual, Level Adjustments

the "#" sign to disconnect (except when the single "*" or "#" is used

- *5 21,22).

Example: To use "*89" as the global connect code and "#89"

as the global disconnect code, enter:

*7 (tone) O (tone) 89 (tone)

6.6.3 Special Connect Code (*7 1)

This code has three features which modify the normal Connect Code sent

by the mobile. Each is explained in it´s own paragraph below. In all

cases, the Special Connect Code is sent directly in front of the

normal Connect Code. For example, using the factory settings for the

two codes, the mobile operator wouid send "*37 *73" to utilize a

Special Connect Code feature. Because the Special Connect Code starts

with a "*", it isn't available when the single tone "*" is used as the

normal Connect Code.

Toll Restriction Bypass - This code will allow users which know

the Special Connect Code to defeat the programmed toll

restrictions for one call only. Toll restriction is

automatically rearmed for the next call upon disconnect. To

enable Toll Restriction Defeat, switch *5 20 should be turned

on. If a toll call override isn't desired turn *5 20 off.

Phone Line In Use Detector - This code will allow a mobile

originated call to break into a call already in progress. This

could be the case when the interconnect shares a line with an

active phone. Switch *5 44 should be off if it is desired to

prevent mobiles from breaking into calls. To interrupt a call

in progress oniy when the Special Connect Code is sent, turn

switch *5 44 is on. Note that if jumper JMP1 is cut, all mobile

calls will break into a call in progress, even without the

Special Connect Code.

The Special Connect Code controls the two outputs "CTRL 1" and

"CTRL 2". See the section describing these outputs for more

information on them.

Program this exactly as the Connect Code in *7 0. To program 38 as

the Special Connect Code, enter:

*7 (tone) 1 (tone) 38 (tone)

6.6.4 Functions (*7 2,3)

The control Function outputs are available at the back connector TB1-

17 and TB1-18. These Functions have no predetermined use in the SDI-

50's normal operation and are provided for customized applications.

These Functions can be turned ON and OFF by DTMF command from the

mobile operator. To use these Control Function

Page # 35

Содержание SDI-50

















































Результаты поиска

Содержание SDI-50

Отзывы:

Похожие инструкции для SDI-50

Бренды по названию

Популярные бренды

CES SDI-50, Руководство пользователя и обслуживания

Результаты поиска

Содержание SDI-50

Отзывы:

Похожие инструкции для SDI-50

Бренды по названию

Популярные бренды