CES SDI-50 Скачать руководство пользователя

Страница: 30 / 48

C.E.S. Model SDI-50 Manual, Level Adjustments

NUMBERS TO BE RESTRICTED *5

____________ON OFF_________

NUMBER 1

1 O

NUMBER 2

1 O

NUMBER 3

1 O

NUMBER 4

1 O

NUMBER 5

1 O

NUMBER 6

1 O

NUMBER 7

1 O

NUMBER 8

1 O

NUMBER 9

1 O

NUMBER O

Example: To have the numeral "1" toll restricted enter the following

sequence:

*5 (tone) 06 (tone) 1 (tone)

To have the numeral "9" restricted enter this sequence:

*5 (tone) 11 (tone) 1 (tone)

Restricted Digits (*5 15,16)

Numbers which were flagged by the switches 00 through 11 will be

restricted as the first dialed digit by using Program Code "*5 15".

Use Code "*5 16" for the second dialed digit.

Restrict Program

From__________________Sequence

First digit ON "*5 15 1"

First digit OFF "*5 15 O"

Second digit ON "*5 16 1"

Second digit OFF "*5 16 O"

Example: To restrict the "flagged" numerals from being the first

digit dialed, but allow it as the second, enter this sequence:

*5 (tone) 15 (tone) 1 (tone)

*5 (tone) 16 (tone) O (tone)

6.5.2

Selectivo Signalling (*5 12)

This Program Code Enables DTMF selective signalling to the

mobiles by "overdialing" a DTMF ANI code from the telephone.

Auto Answer (*5 35) must also be turned on for this to work.

The Ínterconnect will answer on the

Page #26

Содержание SDI-50

















































Результаты поиска

Содержание SDI-50

Отзывы:

Похожие инструкции для SDI-50

Бренды по названию

Популярные бренды

CES SDI-50, Руководство пользователя и обслуживания

Результаты поиска

Содержание SDI-50

Отзывы:

Похожие инструкции для SDI-50

Бренды по названию

Популярные бренды