CENTURION SYSTEMS SECTOR II Скачать руководство пользователя

Страница: 27 / 84

page 27

www.centsys.com

Once the installation has been successfully completed and tested, it is important to

explain the operation and safety requirements of the system to the end-user.

NEVER ASSUME THE USER KNOWS HOW TO SAFELY OPERATE AN AUTOMATED

BARRIER!

Even if the user has used one before, it does not mean he knows how to SAFELY operate

it. Make sure that the user fully understands the following safety requirements before

finally handing over the site.

The following needs to be understood by the user:

• How to operate the manual release mechanism

(Show them how by demonstration)

• How the safety loops and all other safety features work

(Show them how by demonstration)

•

All the features and benefits of the operator, i.e. Safety loops, etc

•

All the safety considerations associated with operating an automated barrier.

The user should be able to pass this knowledge on to all other users of the

automated system and must be made aware of this responsibility

• Do not activate the barrier unless you can see it and can determine that its

area of travel is clear of people, pets, or other obstructions

•

NO ONE MAY GO UNDER A MOVING BARRIER

. Always keep people and

objects away from the barrier

•

NEVER LET CHILDREN OPERATE OR PLAY WITH THE BARRIER

CONTROLS

, and do not allow children or pets near the barrier area

•

Be careful with moving parts and avoid close proximity to areas where fingers

or hands could be pinched

• Secure all easily-accessed barrier operator controls in order to prevent its

unauthorised use

• Keep the automated barrier system properly maintained, and ensure that all

working areas are free of objects that could affect its operation and safety

• On a monthly basis, check the obstruction detection system

and safety devices for correct operation

• All repair and service work to this product must be done

by a suitably qualified person

• This product was designed and built strictly for the use indicated in this

documentation. Any other use, not expressly indicated here, could compromise

the good condition/operation of the product and/or be a source of danger!

Neither Centurion Systems (Pty) Ltd, nor its subsidiaries, accepts any liability caused by

improper use of the product, or for use other than that for which the automated system

was intended.

Ensure that the customer is in possession of the user guide and that you have

completed the installation details in the back of the manual.

INSTALLATION HANDOVER

SECTION 6

6. Installation Handover

Содержание SECTOR II





















































































Результаты поиска

Содержание SECTOR II

Отзывы:

Похожие инструкции для SECTOR II

Бренды по названию

Популярные бренды

CENTURION SYSTEMS SECTOR II, Руководство по установке

Результаты поиска

Содержание SECTOR II

Отзывы:

Похожие инструкции для SECTOR II

Бренды по названию

Популярные бренды